说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 淬火
1)  quenching [英][kwentʃ]  [美][kwɛntʃ]
淬火
1.
Heat transfer coefficient measurement and calculation on the composite surface of parts quenching;
工件淬火过程表面综合换热系数的测算
2.
Control and analysis of quenching deformation for bearing ring;
轴承套圈淬火变形的控制与分析
3.
Effect of quenching on microstructure and properties of TiCp/Fe composite in (Ti-Fe)-Al-C system;
淬火处理对(Ti-Fe)-Al-C体系TiCp/Fe复合材料组织及性能的影响
2)  quench [英][kwentʃ]  [美][kwɛntʃ]
淬火
1.
Effect of precipitate free zone quench-induced on fracture behavior of Al-Zn-Mg-Cu alloys;
淬火无析出区对Al-Zn-Mg-Cu合金断裂行为的影响
2.
A study on quenching technology in zero-time heat of circular chain using in mine;
矿用圆环链“零保温”淬火工艺的研究
3.
The influence of zero time holding quenching temperature on the 20 MnV steel's strength and hardness;
“零保温”淬火温度对20MnV钢强度和硬度的影响
3)  hardening [英]['hɑ:dəniŋ]  [美]['hɑrdnɪŋ]
淬火
1.
Research on a method of large and medium-sized gear surface hardening;
大中型齿轮表面淬火方法的研究
2.
Effect of Hardening Temperature on Propagation Rate of Fatigue Crack of Steel 60Si2Mn and Steel GCr15;
淬火温度对60Si2Mn和GCr15钢疲劳裂纹扩展速率的影响
4)  quencher [英]['kwentʃə]  [美]['kwɛntʃɚ]
淬火
1.
Quencher is a important means to optimize structure of work piece, and it is also a foundation technique in mechanical industry.
淬火是实现工件组织结构优化的一个重要手段,也是机械行业的一项重要基础技术,它对于提高和控制材料的性能,充分发挥材料的性能潜力,节省原材料,减少能耗,提高产品的可靠性,延长其使用寿命,并提高生产单位的经济效益等都具有十分重要的意义。
5)  quenching process
淬火
1.
Numerical simulation of flow and heat transfer during quenching process;
淬火过程流动与传递现象数值模拟
2.
A model is presented for the simulation of a metal workpiece quenching process which is based on two-phase flow and boiling heat transfer.
淬火过程中流固耦合传热与汽液两相流动计算进行了研究,从两相流动与沸腾换热基础理论出发,推导出金属块淬火过程中温度场分布的流固耦合求解控制方程和计算方法。
6)  quenching and tempering
淬火回火
1.
The development and current application situation as well as achievements of heat treatment equipment in annealing,quenching and tempering,carburization and induction heating of bearing parts at home and abroad were discussed.
论述了国内外轴承零件退火、淬火回火、渗碳和感应加热等热处理装备的开发、应用现状和成果 ,提出了国内轴承热处理装备技术水平与工业发达国家之间的差距以及国内外轴承热处理装备今后的发展趋
补充资料:淬火
淬火
quenching 
    将金属工件加热到某一适当温度并保持一段时间,随即浸入淬冷介质中快速冷却的金属热处理工艺。常用的淬冷介质有盐水、水、矿物油、空气等。淬火可以提高金属工件的硬度及耐磨性,因而广泛用于各种工、模、量具及要求表面耐磨的零件(如齿轮、轧辊、渗碳零件等)。通过淬火与不同温度的回火配合,可以大幅度提高金属的强度、韧性及疲劳强度,并可获得这些性能之间的配合(综合机械性能)以满足不同的使用要求。另外淬火还可使一些特殊性能的钢获得一定的物理化学性能,如淬火使永磁钢增强其铁磁性、不锈钢提高其耐蚀性等。淬火工艺主要用于钢件。常用的钢在加热到临界温度以上时,原有在室温下的组织将全部或大部转变为奥氏体。随后将钢浸入水或油中快速冷却,奥氏体即转变为马氏体。与钢中其他组织相比,马氏体硬度最高。钢淬火的目的就是为了使它的组织全部或大部转变为马氏体,获得高硬度,然后在适当温度下回火,使工件具有预期的性能。淬火时的快速冷却会使工件内部产生内应力,当其大到一定程度时工件便会发生扭曲变形甚至开裂。为此必须选择合适的冷却方法。根据冷却方法,淬火工艺分为单液淬火、双介质淬火、马氏体分级淬火和贝氏体等温淬火4类。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条