1) stainless steel
不锈钢
1.
Vacuum hot roll bonding of TC4 titanium alloy and 0Cr18Ni10Ti stainless steel;
TC4钛合金与0Cr18Ni10Ti不锈钢真空热轧连接
2.
Research on cyclic ion nitriding technology catalyzed by rare earth for 2Cr13 stainless steel;
2Cr13不锈钢的稀土催渗循环离子渗氮工艺研究
3.
Analysis of the components of acid chemical coloring solutions for stainless steel;
不锈钢酸性化学着色液成分的分析方法
2) stainless steels
不锈钢
1.
Research of Rare-earth Cerium Conversion Film on Stainless Steels;
不锈钢稀土铈转化膜的研究
2.
Valve for precipitation-hardenable stainless steels;
沉淀硬化不锈钢及其在阀门上的应用
3.
The pitting corrosion of 304 and 316 stainless steels has been studied by monitoring the evolution process of corrosion current with temperature in NaCl solutions with different concentration under constant applied potentials.
采用外加恒定电位下腐蚀电流-温度扫描的方法分别研究了304、316不锈钢在不同浓度NaC l水溶液中的临界点蚀温度。
3) 2Cr13 stainless steel
2Cr13不锈钢
1.
Influence of the TiN film layer on the anti-erosion performance of the 2Cr13 stainless steel blade
TiN膜层提高2Cr13不锈钢叶片的抗冲刷腐蚀性能
2.
Study of hot deformation microstructure and properties for 2Cr13 stainless steel containing rare earth Y
含稀土元素Y的2Cr13不锈钢热变形组织与性能研究
3.
Effect of tempering temperature on stress-corrosion cracking and mechanical hysteresis of 2Cr13 stainless steel
回火温度对2Cr13不锈钢应力腐蚀开裂和力学滞后的影响
4) 1Cr13 stainless steel
1Cr13不锈钢
1.
Vacuum brazing between TiC/NiCr cermets and 1Cr13 stainless steel;
TiC/NiCr金属陶瓷与1Cr13不锈钢的真空钎焊
2.
Titanium coating had been deposited on 1Cr13 stainless steel substrate using cold spray technique.
0MPa,载气温度为500℃的状态下,用冷喷涂的方法在1Cr13不锈钢基体上制备了钛金属涂层。
3.
TiC/Ti(C, N)/TiN multi-layer coatings are prepared on the 1Cr13 stainless steel substrate by the technique of Chemical Vapour Deposition, and the fretting wear behaviour of 1Cr13 stainless steel and TiC/Ti(C, N)/TiN coatings are investigated and studied contrastively from 25℃ to 400℃ in the gross slip regime.
采用化学气相沉积(CVD)技术,在1Cr13不锈钢基体上制备TiC/Ti(C,N)/TiN复合涂层。
5) 254SMo stainless steel
254SMo不锈钢
6) 316L stainless steel
316L不锈钢
1.
Warm compaction technics of 316L stainless steel powder;
316L不锈钢粉末的温压工艺研究
2.
Influence of heat-treatment on the microstructure and properties of 316L stainless steel;
热处理对316L不锈钢组织和性能的影响
3.
Effect of surface mechanical attrition treatment on microstructures and mechanical properties of 316L stainless steel;
表面机械研磨处理对316L不锈钢组织和性能的影响
补充资料：不锈钢
| 不锈钢 stainless steel 耐空气、蒸汽、水等弱腐蚀介质和酸、碱、盐等化学浸蚀性介质腐蚀的钢。又称不锈耐酸钢。实际应用中，常将耐弱腐蚀介质腐蚀的钢称为不锈钢，而将耐化学介质腐蚀的钢称为耐酸钢。由于两者在化学成分上的差异，前者不一定耐化学介质腐蚀，而后者则一般均具有不锈性。不锈钢的耐蚀性取决于钢中所含的合金元素。铬是使不锈钢获得耐蚀性的基本元素，当钢中含铬量达到12％左右时，铬与腐蚀介质中的氧作用，在钢表面形成一层很薄的氧化膜（ 自钝化膜），可阻止钢的基体进一步腐蚀。除铬外，常用的合金元素还有镍、钼、钛、铌、铜、氮等，以满足各种用途对不锈钢组织和性能的要求。不锈钢通常按基体组织分为：①铁素体不锈钢。含铬12％～30％。其耐蚀性、韧性和可焊性随含铬量的增加而提高 ， 耐氯化物应力腐蚀性能优于其他种类不锈钢。②奥氏体不锈钢。含铬大于18％，还含有 8％左右的镍及少量钼、钛、氮等元素。综合性能好，可耐多种介质腐蚀。③奥氏体 - 铁素体双相不锈钢。兼有奥氏体和铁素体不锈钢的优点，并具有超塑性。④马氏体不锈钢。强度高，但塑性和可焊性较差。
|
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条