说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 热处理工艺
1)  heat treatment process
热处理工艺
1.
Analysis and research on the influence of die material and heat treatment process to die life;
模具材料及热处理工艺对模具寿命影响分析与研究
2.
Effect of heat treatment processing on phases and microstructures of (111) orientation preference Pt films;
热处理工艺对(111)取向Pt薄膜物相与结构的影响
3.
Study of heat treatment process of 1Cr5Mo alloy seamless steel pipe;
1Cr5Mo合金无缝钢管的热处理工艺研究
2)  heat treatment
热处理工艺
1.
Effect of heat treatment processing on the microstructure and properties of hot extrusion-deformed FGH95 alloy;
热处理工艺对热挤压变形粉末高温合金FGH95组织与性能的影响
2.
Influence of heat treatment on SA213-T23 weld joint's properties;
热处理工艺对SA213-T23焊接接头性能的影响
3.
Effects of heat treatment on mechanical properties of PC steel bar;
热处理工艺对建筑用PC钢棒强韧性的影响
3)  heat treatment technology
热处理工艺
1.
Effect of heat treatment technology on K_(IC)~J and da/dN of 14Cr1MoR steel;
热处理工艺对14Cr1MoR钢K_(IC)~J和da/dN的影响
2.
The common structural defect of large-scale rudder horn casting steel and its cause of flaw were analyzed,the smelting and heat treatment technology of casting steel was pointed out as well.
分析了挂舵臂铸钢件常见的组织缺陷及产生原因,提出了铸钢件的冶炼及热处理工艺
3.
Through researching N80Q steel kind and the heat treatment technology,we have successfully developed and produced N80Q grade oil casing which meets the API standard and the user's requirement.
包钢通过对N80Q钢种和热处理工艺的研究,成功地开发生产了性能满足标准要求和用户需要的N80Q钢级石油套管。
4)  heat-treatment technology
热处理工艺
1.
This article studies the heat-treatment technology of steel 45 rubber forming dies and the influence of the heat-treatment technology on its microstructure and properties.
主要研究了45钢橡胶成型模具的热处理工艺,以及热处理工艺对其组织和性能的影响。
2.
The 60Si2 Mn steel was selected to investigate the effect of differentoriginal before boronization,different heat-treatment technology after boronization andboronization time on wearability of metals.
研究了60Si_2Mn渗硼不同原始组织、渗硼后不同热处理工艺及不同渗硼时间对材料耐磨性的影响规律,并确定出不同情况下耐磨性最好的工艺规程。
5)  heat treatment technique
热处理工艺
1.
The heat treatment technique for 35CrMo steel to get lath martensite microstrure and the contact fatigue of this lath martensite were researched.
研究了 35Cr Mo钢获得板条马氏体的热处理工艺 ,并对其获得的板条马氏体组织进行了接触疲劳试验 ,结果发现板条马氏体的接触疲劳寿命为调质态的 4倍
2.
The influence of the parameter of heat treatment technique on electromagnetic property of silicon steel slice is inquired into here.
探讨了热处理工艺参数对硅钢片电磁性能的影响。
6)  heat treatment processing properties
热处理工艺性能
1.
Study on comparing of heat treatment processing properties of 20CrNi2Mo and 20Cr2Ni4 used in heavy-duty gears;
重载齿轮用20CrNi2Mo和20Cr2Ni4钢热处理工艺性能对比研究
补充资料:45钢和40Cr钢调质的热处理工艺
45钢40Cr钢调质                         
    调质是淬火加高温回火的双重热处理,其目的是使工件具有良好的综合机械性能。
    调质钢有碳素调质钢和合金调质钢二大类,不管是碳钢还是合金钢,其含碳量控制比较严格。如果含碳量过高,调质后工件的强度虽高,但韧性不够,如含碳量过低,韧性提高而强度不足。为使调质件得到好的综合性能,一般含碳量控制在0.30~0.50%。

    调质淬火时,要求工件整个截面淬透,使工件得到以细针状淬火马氏体为主的显微组织。通过高温回火,得到以均匀回火索氏体为主的显微组织。小型工厂不可能每炉搞金相分析,一般只作硬度测试,这就是说,淬火后的硬度必须达到该材料的淬火硬度,回火后硬度按图要求来检查。 

工件调质处理的操作,必须严格按工艺文件执行,我们只是对操作过程中如何实施工艺提些看法。


   1、 45钢的调质
   45钢是中碳结构钢,冷热加工性能都不错,机械性能较好,且价格低、来源广,所以应用广泛。它的最大弱点是淬透性低,截面尺寸大和要求比较高的工件不宜采用。


   45钢淬火温度在A3+(30~50) ℃,在实际操作中,一般是取上限的。偏高的淬火温度可以使工件加热速度加快,表面氧化减少,且能提高工效。为使工件的奥氏体均匀化,就需要足够的保温时间。如果实际装炉量大,就需适当延长保温时间。不然,可能会出现因加热不均匀造成硬度不足的现象。但保温时间过长,也会也出现晶粒粗大,氧化脱碳严重的弊病,影响淬火质量。我们认为,如装炉量大于工艺文件的规定,加热保温时间需延长1/5。


   因为45钢淬透性低,故应采用冷却速度大的10%盐水溶液。工件入水后,应该淬透,但不是冷透,如果工件在盐水中冷透,就有可能使工件开裂,这是因为当工件冷却到180℃左右时,奥氏体迅速转变为马氏体造成过大的组织应力所致。因此,当淬火工件快冷到该温度区域,就应采取缓冷的方法。由于出水温度难以掌握,须凭经验操作,当水中的工件抖动停止,即可出水空冷(如能油冷更好)。另外,工件入水宜动不宜静,应按照工件的几何形状,作规则运动。静止的冷却介质加上静止的工件,导致硬度不均匀,应力不均匀而使工件变形大,甚至开裂。


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条