1) slab caster
板坯连铸机
1.
Brief Introduction for Technical Equipment of No.4 Slab Caster in Liugang;
柳钢4号板坯连铸机的技术设备简介
2.
The application of air/oil lubrication on slab caster;
油气润滑技术在板坯连铸机上的应用
3.
The erection and commissioning of 250×400 two-strand continuous slab caster;
250×1400双流板坯连铸机的安装调试
2) slab continuous caster
板坯连铸机
1.
Application of roll type electromagnetic stirring in slab continuous caster;
板坯连铸机辊式电磁搅拌的应用实践
2.
Application of casting technological process of the slab continuous caster;
板坯连铸机工艺技术的应用
3.
Application of numerical simulation in project engineering of slab continuous caster;
仿真计算在板坯连铸机工程设计中的应用
3) Slab Continuous Casting Machine
板坯连铸机
1.
This text mainly introduces the automation control of 1700 Slab Continuous Casting Machine in TangGang Steel and it's production sequence.
本文主要介绍了唐钢1700板坯连铸机的自动化控制和生产工序。
2.
According to the requirements of structural adjustment, a 1×1 strand slab continuous casting machine was installed in No.
根据结构调整的需要 ,济钢新建第三炼钢厂配置了一机一流板坯连铸机 ,向中厚板厂提供优质板坯。
3.
3 slab continuous casting machine cannot be to normal work for a long time.
3#板坯连铸机二切工序一直不能正常工作 ,采用了在线切割工艺 ,根据切割条件和切割周期等参数 ,结合板坯连铸出坯线短、车间小的特点 ,确定二切机的位置在距一切终止点 15 m处。
5) thin slab caster
薄板坯连铸机
1.
Fault diagnosis of the hydraulic oscillation system of thin slab caster at Tangshan Steel;
唐钢薄板坯连铸机液压振动系统的故障诊断
2.
The present paper analysed process and casting condition of low carbon steel for thin slab caster of Bengang.
对本钢薄板坯连铸机低碳钢的生产从浇注工艺方面进行分析。
3.
To increase further more the output of thin slab caster, we reformed it: increasing the thickness of tap hole of mold,adopting liquid-core reduction technique of third generation and mold non-sinusoidal vibration technique.
为进一步提高薄板坯连铸机的生产能力,邯钢连铸连轧厂对一期连铸机进行了升级改造,增大了结晶器出口厚度,采用了第3代液芯压下技术、结晶器非正弦振动等新技术,改造后的生产应用表明,板坯的表面质量和连铸机的产量有很大提高。
6) FTSC thin slab caster
FTSC薄板坯连铸机
1.
The causes of breakout during the production of low carbon steel for cold rolling by Tanggang FTSC thin slab caster were analysed and the optimization countermeasures such as the control of mould taper,the copper plate shape of mould narrow side and SEN shape were put forward.
分析了唐钢FTSC薄板坯连铸机生产低碳冷轧用钢过程中漏钢的成因;提出了优化锥度控制、改进结晶器窄面铜板形状和优化水口形状等技术措施。
补充资料：1350mm双流板坯连铸机(重庆钢铁设计研究院设计)
1350mm双流板坯连铸机(重庆钢铁设计研究院设计)
叠 135Omm双流板坯连铸机(重庆钢铁设计研究院设计)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条