说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 挤出成型机
1)  extruder [eks'tru:də]
挤出成型机
1.
Some innovative technologies for resins,additives,injection machines and extruders show- cased on the 21~(th) International Exhibition on Plastics and Rubber Industries were introduced.
介绍了第二十一届中国国际塑料橡胶工业展览会(ChinaplaS2007)上展出的部分新材料、新设备和新技术,包括树脂、助剂、注射成型机、挤出成型机等。
2)  extrusion molding
挤出成型
1.
The research progress in using supercritical CO2 as a plasticizer to reduce the viscosity of polymer melt during extrusion molding and as a foaming agent to make microcellular foams is introduced and the further researches are pointed out.
详述了国内外在超临界二氧化碳降低挤出成型过程中聚合物的熔体粘度和作为发泡剂制备微孔塑料制品两方面的研究进展,指出了目前国内外在超临界二氧化碳(SC-CO2)应用于聚合物挤出成型方面存在的问题。
2.
In the process of PVC low foaming solid sheet extrusion molding,it is critical to control the folw and foaming of the molten polymer.
在PVC低发泡实心板挤出成型中,控制聚合物熔体的流动和发泡是保证产品质量的关键,重点介绍了生产工艺和原理,并分析了生产中的技术要点,提出了解决的办法。
3.
The self-made new type of hydraulic vibration extrusion equipment was adopted to study the rheological behavior of high density polyethylene(HDPE) under vibration extrusion molding.
利用自行研制的新型液压振动挤出装置研究了高密度聚乙烯(HDPE)在振动场中挤出成型时的流变行为。
3)  extrusion moulding
挤出成型
1.
It introduced the extrusion moulding technology of pvc surface-crusting low-foamed wided door sheet.
介绍了PVC结皮低发泡宽幅门板的挤出成型技术。
2.
This article is about the new development in extrusion moulding field, and introduces the new extrusion moulding technique and equipment at K2001.
综述了挤出成型技术领域近年来一些新的发展趋势。
3.
This paper introduces the production technology of the injection and extrusion moulding of Nylon 11.
介绍尼龙11的注射成型和挤出成型工艺,并讨论了生产中易出现的问题及其解决办法。
4)  extrusion [英][eks'tru:ʒən]  [美][ɛk'struʒən]
挤出成型
1.
Studies on the Formation of Homogeneous Ploymer gas Phase in Microcellular Foam Extrusion;
微孔发泡塑料挤出成型中聚合物-气体均相体系形成研究
2.
Novel Method and Epuipment for the Polymer Extrusion Processing;
聚合物挤出成型的新方法与新设备
3.
The impacts of magnetic powder sizes and contents to the fluidity of bonded NdFeB for injection molding and extrusion;
不同磁性粉末装载量和磁性粉末粒度对粘结NdFeB注射、挤出成型流动性能的影响
5)  Extrusion forming
挤出成型
1.
The analysis and discussion were made on various processing-control factors in extrusion forming procedures with the modified extinction ABS resin which could be made by mixing SBS and ABS resins and obtaining their granulations.
针对采用SBS与ABS共混改性、造粒制得的改性消光ABS树脂在挤出板材成型生产过程中的各种工艺控制因素进行了分析和探讨,并分别对改性消光ABS、美国消光CGA1000以及未消光台湾PA747S等原料之挤出成型板材的表面形态结构和光泽度进行了测试,结果表明:改性消光ABS的各项性能指标均达到或优于美国消光料CGA1000。
6)  extrusion process
挤出成型
1.
Based on the characteristic of the plastic profile extrusion process and the theories of rheology and hydrokinetics etc.
针对异型材挤出成型流动过程的特点,基于流变学和流体动力学理论,经合理假设,建立了描述其成型过程的三维等温黏弹性理论模型,并通过DEVSS/SUPG,EVSS法,Mini-Element最小元法和罚函数法等稳态有限元技术,建立了与该模型相适应的快速收敛的稳态有限元数值算法,并以此通过有限元数值模拟,系统研究了黏弹流变性能参数和工艺参数对异型材挤出胀大的影响规律。
2.
In the dissertation high-temperature corundum honeycombed ceramic regenerative body was prepared by an extrusion process, a-Al2O3 minute powder as main raw material, clay, CMC etc as plasticizers, tung oil etc as lubricator.
以a-Al_2O_3微粉料为主原料,采用粘土、羧甲基纤维素(CMC)等有机-无机复合增塑剂,加入桐油等作为润滑剂,采用挤出成型法制备刚玉质高温型蜂窝陶瓷蓄热体。
补充资料:接触成型
分子式:
CAS号:

性质:在不加压或稍加压(通常小于68kPa)的情况下制造增强塑料制品的方法。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条