1) cold rolled sheet
冷轧薄板
1.
Loop analysis of continuous pickling line for cold rolled sheet of Tangshan Iron and Steel Co., Ltd.;
冷轧薄板连续酸洗线的活套分析
2.
Technology characteristics of cold rolled sheet unit of Benxi Steel Posco Cold Rolled Co.,Ltd.;
本钢浦项冷轧薄板机组的工艺特点
2) cold-rolled sheet
冷轧薄板
1.
Experimental study of recrystallization of cold-rolled sheets produced by CSP hot bands;
CSP冷轧薄板再结晶试验研究
2.
The main production process,equipments collocation and advanced technologies of the primary cold-rolled sheet project are introduced in this paper.
介绍了莱钢冷轧薄板(一期)工程的主要生产工艺、设备配置及先进技术。
3.
Newly-built cold-rolled sheet project in Jigang is introduced and the process flows, technological characteristics and the technical parameters of main facilities in 110×104 tons continuous pickling line, 84×104 tons cold rolling line, 43×104 tons annealing line, 48×104 tons leveling line and 33×104 tons recoiling and cutting line are analyzed with emphasis.
介绍了济钢新建冷轧薄板项目的情况,重点介绍了110万t连续酸洗线、84万t冷轧线、43万t退火线、48万t平整线和33万t重卷分卷线的工艺流程、技术特点及主要设备技术参数。
3) cold-rolled strip
冷轧薄板
1.
A cold-rolled strip plate-profile recognition method was presented to improve the detection accuracy based on image morphology processing method.
为了解决冷轧薄板板形识别问题,采用基于形态学的图像处理方法。
2.
A cold-rolled strip plate-profile recognition method was presented to improve the detection accuracy based on image processing.
为了解决冷轧薄板板形识别问题,采用基于图像处理的方法,对图像进行直方图均衡化,使处理后的图像对比度、图像边界的清晰度有了很大的提高,并在此基础上再进行形态学增强,改善图像效果。
4) cold rolled sheets
冷轧薄板
1.
To make high desulphurization rate of steels in ladle furnace refining for cold rolled sheets,w([O]) has to be decreased to a very low level,which easily results in w() out off the specification range of the steels.
炉外精炼过程钢液氧含量对脱硫效率影响显著,对冷轧薄板钢种如在LF中进行深度脱硫,由于必须将钢液氧含量降至很低水平,容易造成钢中硅含量超标等问题。
5) cold rolled thin plate
冷轧薄板
1.
The appraise standard of drawing properties of cold rolled thin plate was reviewed.
概述了冷轧薄板的冲压性能的评价指标,详细介绍了冷轧薄板的化学成分、织构和晶粒尺寸、表面质量、厚度尺寸公差、冷轧工艺条件、拉伸试验值对冷轧薄板冲压性能的影响,并应用ANS YS/LS-DYNA软件对板材弯曲成形过程进行了模拟。
2.
Plastic deformation heat and friction heat is the two principle factor which caused the temperature increment of cold rolled thin plate.
采用包含滑动摩擦和粘着摩擦在内的预位移 滑动摩擦模型较准确地计算了轧制区摩擦热 ,并综合考虑轧件塑性变形热 ,推导了冷轧薄板温升计算公式。
3.
The research on rolling force prediction for cold rolled thin plate by a mixed friction model including stick and slip frictions was carried out, and a new rolling force prediction model was obtained.
作者采用包括粘着摩擦和滑动摩擦在内的混合摩擦模型,研究了冷轧薄板轧制力预报问题,建立了轧制力预报新模型。
6) CSP Cold Rolling Sheet
CSP冷轧薄板
补充资料：薄板冷轧
以单片、无前后张力冷轧的方法生产薄板。由于轧制速度低(小于2m/s)，厚度控制困难，且成材率低，现在多用于生产特定的合金钢和某些有色金属板材（见带钢冷轧、板带材）。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条