说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 熔体
1)  melt [英][melt]  [美][mɛlt]
熔体
1.
Decomposition Behavior of HFC-134a on the Heated Magnesium and Magnesium Alloy Melt Surface;
HFC-134a气体在保护镁及合金熔体过程中的分解行为
2.
High temperature Raman spectra and micro-structure of Bi_4Ge_3O_(12) crystal and its melt;
Bi_4Ge_3O_(12)晶体及其熔体结构的高温拉曼光谱研究
3.
Effect of Sn content on the structural properties of the Bi-Sn alloy melt;
Sn的质量分数对Bi-Sn合金熔体结构的影响
2)  melts
熔体
1.
Viscosity,metastable phase,phase transition and phase diagram of melts Ⅰ.The theory on viscosity and metastable phase for melts;
熔体的粘度,亚稳相,相变和相图 Ⅰ.熔体的粘度理论和亚稳相
2.
Combining with reported vibrational spectra, X-ray and MD simulation work of the carbonates, the structure characteristics of the carbonate melts and different effects on the vibrational behavior which is due to the alkali cations were discuss.
报导了用高温激光Raman光谱仪测定了不同温度 (至 1 2 73K)下固体和熔融态的Li2 CO3、Na2 CO3和K2 CO3的Raman光谱 ,分析了CO2 -3 对称伸缩振动模随温度升高的波数移动情况和半高宽的变化 ,结合前人的振动光谱和X射线测试结果以及分子动力学模拟工作 ,讨论了碳酸盐熔体的结构特征 ,以及不同的碱金属离子对碳酸根离子的振动造成的不同影
3.
The melts of smelting reduction with iron bath has peculiar behaviour for high concentration and high reduction rate of FeO.
铁浴式熔融还原熔渣内FeO浓度高,使熔体的组成和性能具有特殊的行为。
3)  In melt
In熔体
1.
The structure of In melt was studied at 280℃, 390℃, 550℃, 650℃, 750℃ respectively by using an elevated temperature Xray diffractometer.
利用高温液态金属X射线衍射仪在280℃、390℃、550℃、650℃、750℃研究了In熔体的结构。
4)  fuse-element
熔体,熔丝,熔片
5)  fluid melt
流体熔体
1.
The most efficient ore components concentration mechanism at the magmatic stage must be the separation of fluid melt.
在岩浆阶段 ,富集金属元素最有效的机制是流体熔体的分离。
6)  melt temperature
熔体温度
1.
Prediction of Injection Pressure and Melt Temperature of Injection Molding by Radial Basis Function Network;
基于神经网络技术的注塑成型注射压力和熔体温度预测
2.
Effects of Melt Temperature on Solidified Structure of Sn-Sb Peritectic Alloy in Ultrasonic Field;
超声场下熔体温度对SnSb合金凝固组织的影响
3.
The stress distribution of polycarbonate injection molded parts is tested by the photo-elastic experiment under different gate type and different melt temperature,and the tensile strength and luminous transmittance are tested.
用光弹实验测试不同浇口类型、不同熔体温度下聚碳酸酯透明注塑制品的应力分布,并测试了制品的拉伸强度和透光率。
补充资料:熔体破裂
分子式:
CAS号:

性质:当胶料挤出速度超过某一极限值时,挤出物表面出现凹凸不平、波浪、竹节、螺旋形畸变以至完全无规的破裂现象,也称弹性湍流。它不仅影响产品质量,也影响产品产量。突其原因是由于挤出时剪切应力过高,熔体各点所表现的弹性应变不一,从而使挤出物在弹性恢复过程中出现畸变,严重时出出断裂现象。影响熔体断裂的主要因素为搞出口型几何尺寸、挤出温度和材料本身的分子量和分子量分布。适当降低分子量,加宽分子量分布,适当提高挤出温度、加大口型间隙、采用喇叭型口型或调节配方都可减轻或避免熔体破裂现象。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条