说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 弯曲试验
1)  bending test
弯曲试验
1.
Metal material bending test is an important item when raw materials come to factory in boiler and pressure vessel manufacturing trade.
金属材料的弯曲试验是锅炉压力容器制造行业进行原材料入厂检验的一项主要检查项目。
2.
Low-temperature bending tests of asphalt mixture under-10℃ have been done by MTS810 material test system.
在MTS810材料试验系统上进行了-10℃下的沥青混合料的低温弯曲试验,通过对大量试验结果的分析和总结,以抗弯拉强度和最大弯拉应变为指标来评价沥青混合料的低温抗裂性能。
3.
In order to promote the industrialization of the FRP fishing boat, the writers consulted a lot of material in our country and abroad, conduct ed bending tests for some slices of FRP ship s bulk, and then bring forward rule s for this kind of test.
为推进玻璃钢渔船 的产业化进程,作者在查阅了大量国内外有关资料的基础上,进行了玻璃钢渔船船体材料切 片的弯曲试验,最终提出了我国玻璃钢渔船船体材料切片的弯曲试验的试验规程,以供我国 今后制定玻璃钢渔船材料试验标准作参考。
2)  Bending experiment
弯曲试验
1.
Research on the Bending Experiment Method on Copper and Cuprum Alloy Contact Wires for Electrified Railways;
电气化铁道用铜及铜合金接触线反复弯曲试验方法的研究
2.
Bending experimented test system of piston rod based on virtual instruments
基于虚拟仪器的活塞杆弯曲试验测试系统
3.
Several experiment methods on the adhesion property between CFRP and concrete are studied and analyzed,of these methods,bending experiment method is easy and very effective.
本文分析了研究CFRP与混凝土之间粘结性能的几种试验方法 ,确定采用简单易行而且十分有效的弯曲试验来研究CFRP加固混凝土结构粘结材料的性能。
3)  bend test
弯曲试验
1.
The roasting test and bend test results .
烘烤试验及弯曲试验表明,该工艺结合力很好。
2.
This paper firstly expatiates the object and purpose of the bend test during the welding procedure qualification.
通过对焊接工艺评定中弯曲试验评定对象和目的的阐述 ,结合国内外的焊接工艺评定标准对弯曲试验的不同要求 ,对焊接接头弯曲试验的力学模型进行了数学分析 ,得出采用不同弯曲试验标准可以得到不同的评定结果。
3.
Through the comparison between the outdated and the lastest standards it is found that althongh the years for preparation of two standards are different,bath for equivalent to the international standard ISO 7438:1985 “metallic materials-bend test” the definite answer has not found out for some questions.
通过新旧标准对比 ,发现两个标准虽然年代不同 ,但均等放采用国际标准ISO 7438:1985金属材料—弯曲试验 ,其中某些问题尚找不出确切的答案。
4)  flexural test
弯曲试验
1.
By flexural test and split test , the effect of part or total replacement of mineral powder with cement on and-cracking performance of asphalt mixture is researched.
通过弯曲试验和劈裂试验,分析了水泥替代部分或全部矿粉对沥青混合料抗裂性能的影响。
5)  bending test
反复弯曲试验;弯曲试验
6)  static beaming test
静弯曲试验
补充资料:弯曲试验
      测定材料承受弯曲载荷时的力学特性的试验,是材料机械性能试验的基本方法之一。弯曲试验主要用于测定脆性和低塑性材料(如铸铁、高碳钢、工具钢等)的抗弯强度并能反映塑性指标的挠度。弯曲试验还可用来检查材料的表面质量。弯曲试验在万能材料机上进行,有三点弯曲和四点弯曲两种加载荷方式(见图)。试样的截面有圆形和矩形,试验时的跨距一般为直径的10倍。对于脆性材料弯曲试验一般只产生少量的塑性变形即可破坏,而对于塑性材料则不能测出弯曲断裂强度,但可检验其延展性和均匀性展性和均匀性。塑性材料的弯曲试验称为冷弯试验。试验时将试样加载,使其弯曲到一定程度,观察试样表面有无裂缝。
  
  参考书目
   R.F. Bunshan , Measurement of Mechanical Proporties,John Wiley & Sons,Inc.,New York,1971.

  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条