说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 硬质合金刀具
1)  carbide tool
硬质合金刀具
1.
New available materials in cutting tools for casting iron are carbide tool, ceramic cutters, cermet cutters and ultrahard cutting tool.
介绍了选择铸铁切削用刀具需考虑的因素,可用于不同牌号铸铁的切削用刀具新材料有硬质合金刀具、陶瓷刀具、金属陶瓷刀具和超硬刀具。
2.
4 GPa and hardness 50HRC and martenstic stainless steel with hardness 30HRC, using (Ti,Al)N coated carbide tool and fine grain carbide tool, respectively, on a DMU-70 evolution 5-axle processing center.
采用涂层硬质合金刀具和细晶粒硬质合金刀具对超高强度合金钢(硬度>50HRC、抗拉强度σb>1。
3.
The main factors affect the quality of carbide tool with CVD coating are discussed from alloy's foundation material and coating to promote the man ufacturing quality and exert the best application property of cutti ng tool.
从合金基体材料、涂层两方面对高精切削加工中应用广泛的CVD涂层硬质合金刀具质量的主要影响因素进行了分析,为从制备工艺上更好地提高涂层刀具的质量,充分发挥刀具的最佳综合使用性能提供了借鉴。
2)  cemented carbide
硬质合金刀具
1.
The diamond film was deposited on WC-6%Co(mass fraction) cemented carbide by DC arc discharged plasma chemical vapor deposition.
低压气相金刚石薄膜硬质合金刀具在直流弧光放电等离子体CVD镀膜设备上制备。
2.
The contrast dry cutting experiments are carried out to study the cutting performance of Ni based PM parts by using ceramic and cemented carbide cutting tools.
对陶瓷刀具和硬质合金刀具进行了镍基粉末冶金零件的干切削对比试验,测量了切削力和加工表面粗糙度,分析了刀具的磨损机理。
3)  hard alloy cutting tools
硬质合金刀具
1.
Aiming at to the question that sticking of cutting tool is serious when using the hard alloy cutting tools to cut austenite non-corrosive steels,this article uses the DICTRA module in thermodynamic software thermoCalc to simulate the atom diffusion between the hard alloy cutting tools and cut work-piece.
针对硬质合金刀具切削奥氏体不锈钢粘刀现象严重的问题,利用热力学软件Thermo-Calc中的TCC模块和D ICTRA模块,模拟了硬质合金刀具与被切削工件之间发生的原子扩散。
2.
In dry cutting conditions within single-factor test,comparative analysis the difference of the PCBN cutter and hard alloy cutting tools milling GCr15 steel.
在干式切削的条件下,采用单因素试验法,比较分析了PCBN刀具和硬质合金刀具铣削轴承钢GCr15的差异。
4)  cemented carbide tool
硬质合金刀具
1.
The cemented carbide tool coated with diamond film is one of the important application of CVD diamond film.
金刚石薄膜涂层硬质合金刀具是CVD金刚石薄膜的重要应用领域之一。
2.
The Co concentration in the etching liquor after different acid corroding time for YG series cemented carbide tools was tested by atomic absorption spectrometry,the hardness change of tools was detected by HRC and the microstructure of diamond film was observed by scanning electron microscope.
采用原子吸收光谱(AAS)标准曲线法对YG系列硬质合金刀具酸蚀后浸蚀溶液中的Co浓度进行了定量测试;采用洛氏硬度(HRC)计跟踪测试了不同酸蚀时间后刀具硬度的变化;采用扫描电子显微镜(SEM)观察了硬质合金刀具酸蚀前后的组织变化及金刚石薄膜的组织形貌。
3.
Based on the high-speed milling experiment for titanium alloy Ti6Al4V with fine grain cemented carbide tool Y330,the tool wear and breakage modes and failure mechanisms were analyzed.
基于用Y330细晶粒硬质合金刀具高速铣削Ti6Al4V钛合金的试验,分析了刀具的损坏形态和失效机理。
5)  cemented carbide cutting tool
硬质合金刀具
1.
The development and the main problems of diamond-coated cemented carbide cutting tools are comprehensively summarized.
概述了CVD金刚石涂层硬质合金刀具的研究现状及存在的问题,重点对近五年CVD金刚石涂层硬质合金刀具基体预处理方法、涂层内应力的表征方法等方面的研究现状进行了综述。
6)  carbide cutting tools
硬质合金刀具
1.
Take difficult-to-cut materials and carbide cutting tools as the research objects, aim at each cutting character, using Rule-based-Reasoning, establish a cutting tools material intelligent selection system which is based on Visual C++6.
以难加工材料和硬质合金刀具为研究对象,针对它们各自的切削加工性,利用基于规则(RBR)推理方法,以Visual C++ 6。
2.
The percentage lf carbide cutting tools consrmed by the world at 2003 and the fast increasing of carbide gear hob was analyzed.
分析了2003年硬质合金刀具在全世界刀具消费值中的比例,及硬质合金齿轮滚刀的迅速发展。
3.
This paper analyzed the changes of Japanese carbide cutting tools in 2003,and the influence of Japanese mould & IT industry on these changes.
分析了2003年日本硬质合金刀具销售值占刀具总销售值的比例,及硬质合金立铣刀的迅速发展。
补充资料:硬质合金刀具科普知识
  刀具是机械制造中用于切削加工的工具,又称切削工具。广义的切削工具既包括刀具,还包括磨具。绝大多数的刀具是机用的,但也有手用的。由于机械制造中使用的刀具基本上都用于切削金属材料,所以"刀具"一词一般就理解为金属切削刀具。切削木材用的刀具则称为木工刀具。
  刀具的发展在人类进步的历史上占有重要的地位。中国早在公元前28~前20世纪,就已出现黄铜锥和紫铜的锥、钻、刀等铜质刀具。战国后期(公元前三世纪),由于掌握了渗碳技术,制成了铜质刀具。当时的钻头和锯,与现代的扁钻和锯已有些相似之处。
  然而,刀具的快速发展是在18世纪后期,伴随蒸汽机等机器的发展而来的。1783年,法国的勒内首先制出铣刀。1792年,英国的莫兹利制出丝锥和板牙。有关麻花钻的发明最早的文献记载是在1822年,但直到1864年才作为商品生产。
那时的刀具是用整体高碳工具钢制造的,许用的切削速度约为5米/分。1868年,英国的穆舍特制成含钨的合金工具钢。1898年,美国的泰勒和.怀特发明高速钢。1923年,德国的施勒特尔发明硬质合金。
  在采用合金工具钢时,刀具的切削速度提高到约8米/分,采用高速钢时,又提高两倍以上,到采用硬质合金时,又比用高速钢提高两倍以上,切削加工出的工件表面质量和尺寸精度也大大提高。
  由于高速钢和硬质合金的价格比较昂贵,刀具出现焊接和机械夹固式结构。1949~1950年间,美国开始在车刀上采用可转位刀片,不久即应用在铣刀和其他刀具上。1938年,德国德古萨公司取得关于陶瓷刀具的专利。1972年,美国通用电气公司生产了聚晶人造金刚石和聚晶立方氮化硼刀片。这些非金属刀具材料可使刀具以更高的速度切削。
  1969年,瑞典山特维克钢厂取得用化学气相沉积法,生产碳化钛涂层硬质合金刀片的专利。1972年,美国的邦沙和拉古兰发展了物理气相沉积法,在硬质合金或高速钢刀具表面涂覆碳化钛或氮化钛硬质层。表面涂层方法把基体材料的高强度和韧性,与表层的高硬度和耐磨性结合起来,从而使这种复合材料具有更好的切削性能。
  刀具按工件加工表面的形式可分为五类。加工各种外表面的刀具,包括车刀、刨刀、铣刀、外表面拉刀和锉刀等;孔加工刀具,包括钻头、扩孔钻、镗刀、铰刀和内表面拉刀等;螺纹加工工具,包括丝锥、板牙、自动开合螺纹切头、螺纹车刀和螺纹铣刀等;齿轮加工刀具,包括滚刀、插齿刀、剃齿刀、锥齿轮加工刀具等;切断刀具,包括镶齿圆锯片、带锯、弓锯、切断车刀和锯片铣刀等等。此外,还有组合刀具。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条