1) 9Cr2Mo steel
9Cr2Mo钢
1.
The microstructure and morphology of bainite of 9Cr2Mo steel austenitized at 1 100℃ and isothermally quenched in salt bath at different temperature were studied by metallographic microscope and SEM.
采用光学显微镜和扫描电子显微镜等技术手段观察了经1 100℃奥氏体化的9Cr2Mo钢在不同温度的盐浴中等温淬火后贝氏体的组织形貌。
2.
Different quenching processes with different temperature have first been designed in experiment,and the best quenching process of 9Cr2Mo steel has been gotten under the biggest hardness,meanwhile the quenching processes show that 9Cr2Mo steel can be fully quenched after both water and oil quenching.
实验中首先设计了不同温度的淬火工艺,得出了9Cr2Mo钢得到最大洛氏硬度下的淬火工艺,同时得出9Cr2Mo钢在水和油中都能淬透;再研究不同回火工艺对9Cr2Mo钢洛氏硬度的影响,得出结果:9Cr2Mo钢的洛氏硬度随回火温度的升高先缓慢下降,当回火温度高于300℃时,随着回火温度的升高明显降低。
3.
The anti-abrasion of 9Cr2Mo steel is higher 72% than that of GCr15 steel.
运用JSM-5610LV扫描电镜对德国产X165CrMoV12钢、国产Cr12MoV钢、9Cr2Mo钢、GCr15钢在不同热处理工艺条件下的金相组织、冲击韧性及耐磨性进行了分析。
2) steel 9Cr2Mo
9Cr2Mo钢
1.
The effect of rare earth elements on thermal shock resistance of cold roller steel 9Cr2Mo was investigated by means of X ray diffraction and metallographic microscopy.
试验结果表明 :稀土元素抑制了热影响区回火时碳化物的析出 ,从而提高了 9Cr2Mo钢抗热冲击性
2.
The effect of rare earth elements on quenching crack resistance of cold roller steel 9Cr2Mo was investigated by means of scanning electron microscope(SEM) and optical microscope.
利用电镜和金相等手段研究了稀土元素对 9Cr2Mo钢抗淬裂性能的影响。
3) 9Cr2Mo steel cold roller
9Cr2Mo钢冷轧辊
4) 9Cr2Mo forged cold-rolled working roll
9Cr2Mo锻钢冷轧工作辊
1.
Analyzing by metallurgical phase and SEM, find out the fracture causation of 9Cr2Mo forged cold-rolled working roll.
通过金相和扫描电镜分析,并配合热处理试验,找出9Cr2Mo锻钢冷轧工作辊断裂失效原因。
5) IF steel
IF钢
1.
The Static Recrystallization Behavior of IF Steel after Ferrite Hot Deformation;
IF钢热变形铁素体的静态再结晶行为
2.
Influence of MgO-SiC material with Al powder on silicon content of IF steel;
含铝粉的MgO-SiC材料对IF钢硅含量的影响
3.
TEM study on recrystallization mechanism of IF steel;
IF钢冷轧及再结晶初期微观组织的TEM研究
6) steel
[英][sti:l] [美][stil]
钢
1.
Analysis of characteristic zones of isothermal superplastic welded joint of heterogeneous steels;
异种钢恒温超塑焊接头特征区域分析
2.
Determination of total boron in steel with microwave digestion and Inductively Coupled Plasma Atomic Emission Spectrometry;
微波消解/ICP-AES法测定钢中全硼
3.
Approach to Research on Cracking of Steel and Relevant Concerns;
钢的裂纹研究思路及应注意的问题
补充资料：compression mo(u)ding powder
分子式：
分子量：
CAS号：
性质：又称塑料粉。压塑料的一种。是用压塑法制热固性塑料制品的粉状原料。主要由热固性树脂（如酚醛树脂、脲醛树脂等）和填料等，经充分混合、滚压、粉碎而得。有些不加填料，有些另加颜料、熟化剂或润滑剂等。重要的有酚醛压塑粉和脲醛压塑粉。见压塑料。
分子量：
CAS号：
性质：又称塑料粉。压塑料的一种。是用压塑法制热固性塑料制品的粉状原料。主要由热固性树脂（如酚醛树脂、脲醛树脂等）和填料等，经充分混合、滚压、粉碎而得。有些不加填料，有些另加颜料、熟化剂或润滑剂等。重要的有酚醛压塑粉和脲醛压塑粉。见压塑料。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条