说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 电弧焊
1)  arc welding
电弧焊
1.
Numerical model of thermal cycle in arc welding of steel plate and sheet;
中厚、薄板快速电弧焊热循环数学模型
2.
Environmental load assessment of arc welding process;
电弧焊过程的环境负荷评价
3.
An example of applying arc welding in repair of kiln and grind mill;
电弧焊在窑磨修理中的应用实例
2)  electric arc welding
电弧焊
3)  arc welding
电[弧]焊;弧焊
4)  arc welding equipment
电弧焊接;电弧焊
5)  shielded metal arc welding
焊条电弧焊
1.
Discussion on safely using electricity in shielded metal arc welding process(3)——Measures to prevent electric shock accidents;
焊条电弧焊用电安全问题的探讨(三)——防止触电事故的措施
2.
Analysis on the Process and Cost of Shielded Metal Arc Welding and CO_2 Gas Shielded Welding
CO_2气体保护焊与焊条电弧焊工艺及成本分析
3.
Single-pass and multi-passes welded joints of 0Cr18Ni9/20 clad pipe were prepared by the use of shielded metal arc welding(SMAW) and E309L super-low carbon austenitic stainless steel electrode.
采用E309L型超低碳奥氏体不锈钢焊条的焊条电弧焊(SMAW,shieldedmetal arc welding)方法制备了0Cr18Ni9/20复合管单层焊和多层焊接头,并应用光学金相、能谱(EDS,energy dispersive spectrum)成分及线扫描、扫描电镜(SEM,scanning electronmicroscope)、X射线衍射以及显微硬度等方法对焊接接头进行了对比分析研究。
6)  welding rod arc welding
焊条电弧焊
1.
This article introduces the experiment that contrasted the welding joint's performance and enameling capability among CO2 gas shielded welding, welding rod arc welding and submerged arc auto-welding, compares the welding cost between CO2 gas shielded welding and welding rod arc welding, analyzes the feasibility of applying CO2 gas shielded welding on enamel glass equipment.
本文对CO_2气体保护焊焊接接头与焊条电弧焊、埋弧自动焊焊接接头的性能、可涂搪性进行了对比试验,并对CO_2气体保护焊和焊条电弧焊两种焊接方法的焊接费用作了比较,进行了搪玻璃设备上应用CO_2气体保护捍的可行性分析。
补充资料:电弧焊

  
  电弧焊
  electric arc welding

  d一onhUhon电弧焊(eleetrie ar。welding)利用电弧作为热源的熔焊方法,简称弧焊(见电坪、电弧加热)。 焊接时,电弧在焊件的接缝处和电极之间燃烧,焊件接缝处的金属和必要时添加的坡充金属受热熔化,形成熔池;电极用手工或机械方法沿焊接方向移动,或电极固定,焊件移动;熔池冷凝后形成焊缝,把焊件连接在一起。 电极分不熔化电极和熔化电极两种。不熔化电极通常用钨极,用以施焊时,可根据需要另加坡充金属。熔化电极在焊接时不仅传导电流,而且其端部不断熔化作为填充金属填在接缝中.熔化电极通常做成焊条和焊丝两种形式。前者多用于手工焊接,后者则多用于自动或半自动焊接。各种金属的焊接各有其适用的焊条或焊丝。电弧焊的主要种类和用途列于表。 电弧焊有电弧温度高、热量集中且容易控制等特电筑娜的主要种类和用途┌─────────────┬─────────────────────────────┬───────┐│名称 │用途(适宜于焊接的材料和焊接厚度值) │适用的辉接位t │├─────────────┼─────────────────────────────┼───────┤│手弧焊 │ 碳钢、合金钢、镶及镶合金、钥及钥合金等(3~20 mm),铸铁 │各种位l ││ │(76 rn们。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条