1) silica sol
硅溶胶
1.
Behavior of silica sol during the anodizing process of magnesium alloy;
硅溶胶在镁合金阳极氧化反应中的成膜作用
2.
Determination of Na Content in Silica Sol by ICP-AES;
ICP-AES测定硅溶胶中Na元素的分析方法研究
3.
Research progress of preparation and application of silica sol;
硅溶胶制备与应用研究进展
2) silica sols
硅溶胶
1.
Effect of the sodium chloride on the gelation of the cationic silica sols
氯化钠对阳离子杂化硅溶胶凝胶化的影响
3) silicasol
[sili'kæsɔl]
硅溶胶
1.
Investigation on preparation of gelled electrolyte with silicasol and gas silica;
硅溶胶与气相二氧化硅配制胶体电解质的研究
2.
Study on the mechanism of coupling modification of styrene/acrylic latex by silicasol
硅溶胶偶联改性苯丙乳液机理研究
3.
Using polyvinyl alcohol(PVA) and polyoxyethylene(10) nonyl phenyl ether(OP-10) as surfactant-low emulsifier,styrene(St)/butyl acrylate(BA)/vinyl acetate(VAc)/2-ethylhexylacrylate(2-EHA) tetrapolymer was synthesized by polymerization of seed emulsion,which took hybridization reaction with silicasol and tetraethyl silicate(TEOS) and organosilicon acrylate hybrid emulsion was made.
采用种子乳液聚合,以聚乙烯醇、壬基酚聚氧乙烯醚作为低皂乳化剂,合成了苯乙烯/丙烯酸丁酯/乙酸乙烯酯/丙烯酸-2-乙基己酯四元共聚乳液,再与硅溶胶、正硅酸乙酯(TEOS)进行杂化反应,制得有机硅丙烯酸酯杂化乳液。
4) silicon sol
硅溶胶
1.
The result showed that hardness of the composites rose with increasing of the silicon sol dosage;when the dosage of silicon sol is greater than 10%(mass fraction),it has weak effects on the material hardness,and bad effects on other mechanical properties of t.
结果表明:随着硅溶胶量的不断增大,材料硬度随之增大,当硅溶胶加入量大于10%(质量分数)时,对材料硬度的影响较小,且不利于材料的其他力学性能。
2.
With tetraethyl ortho-silicate (TEOS) as main material and through the polymerization-sol process, silicon sol is obtained and is compounded with styrene-acrylic latex to give complex binder, then the silicon sol and styrene-acrylic complex road-mark coatings.
采用正硅酸乙酯(TEOS)为主要原料,以聚合溶胶法制备硅溶胶,制得的硅溶胶与苯丙乳液冷拼复配得到复合基料,再以该基料制得硅溶胶—苯丙复合路标涂料。
3.
The preparation of nano-silica by chem-deposit method is carried out by using basic silicon sol and inorganic acid as materials.
以碱性硅溶胶和无机酸为原料,水和甲醇为反应介质,加入适宜的分散剂,反应体系在适宜的反应温度和pH值下反应一定时间,经过真空脱水干燥和超细筛网筛分得到稳定的纳米二氧化硅粉体。
5) Colloidal silica
硅溶胶
1.
Application of Colloidal Silica-sodium Silicate Compound Coating in Investment Casting;
硅溶胶—水玻璃复合涂料在精铸生产中的应用
2.
Over five years prouction practice we can prove that the process of ceramic shell mould used in colloidal silica in investment casting is coming to maturity and provide the technical guarantee for producing the quality ceramic shell mould and precise castin
介绍用石蜡-硬脂酸低温模料,生产铸件的熔模和用精密铸造硅溶胶,作为制壳粘结剂,制造铸件的模壳的工艺要求。
3.
The preparation of colloidal silica is introduced.
以正硅酸乙酯为原料,分别以盐酸、硫酸、甲酸、天冬氨酸或其混合酸为水解催化剂制备硅溶胶。
6) Ti-Si sol
钛硅溶胶
1.
High titanium loading MCM-41 was prepared via the novel post-grafting method by impregnating calcined MCM-41 into the Ti-Si sol.
1催化剂的制备采用文献[6]的方法制备钛硅溶胶。
补充资料：硅溶胶
无色半透明或乳白色粘液。溶于氢氟酸和氢氧化钠溶液，不溶于水和其他无机酸。加热凝固成硅胶，冷至0℃以下 则成粘液。
应用 轻纺工业用作羊毛和轻纱上浆剂。冶金工业用作轧钢工程矽钢片的涂料。无机工业用于制备分子筛。精密铸造工业用于代替原硅酸乙酯，以改善劳动条件．并对铸件表面光洁度及型完强度均有提高，是铸型型壳的优良粘结剂。分析化学中用作色谱吸收剂，薄层色谱试剂和粘结剂。远红外技术中用作远红外波辐射涂料。此外，也用于固体硅电瓶的制造等。
应用 轻纺工业用作羊毛和轻纱上浆剂。冶金工业用作轧钢工程矽钢片的涂料。无机工业用于制备分子筛。精密铸造工业用于代替原硅酸乙酯，以改善劳动条件．并对铸件表面光洁度及型完强度均有提高，是铸型型壳的优良粘结剂。分析化学中用作色谱吸收剂，薄层色谱试剂和粘结剂。远红外技术中用作远红外波辐射涂料。此外，也用于固体硅电瓶的制造等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条