1) eccentric sleeve
偏心套
1.
Application of eccentric sleeve to adjust the contact pattern for helical gears;
利用轴承偏心套调整斜齿轮副的接触状态
2.
To guarantee the implementation of the adjustment precision of the overlap in the trimming disk shear,an analysis of the principle of the mechanism and the derivation of the mathematical control model have been made,through which the design precision of eccentric sleeve,essentials of the fabrication technology,assembly method,unique drives and electric control system,etc.
为了保证切边圆盘剪重叠量调整精度的可靠实现,通过对切边圆盘剪重叠量调整机构原理分析及控制数学模型的推导,对偏心套的设计精度、制造工艺要领、装配方法、独特的传动机构及电气控制等方面进行了详细阐述,保证了高精度切边圆盘剪重叠量精度的可靠实现。
3.
4 car hauler's eccentric sleeve not only has the disadvantages of heavy labor intensity,low efficiency,but can't satisfy the need of batch process.
4调度绞车的偏心套,按传统的加工工艺存在着劳动强度大,效率低,而且无法满足批量生产的需要。
2) casing eccentricity
套管偏心
1.
Aiming at the problem that eccentricity of casing in circular hole happened in thermal well,the finite element model is established and the effect of casing eccentricity on wellbore temperature field,casing stress and displacement were analyzed.
针对热采井中套管在圆形井眼中出现偏心的问题建立了有限元模型,分析套管偏心对井筒温度场和套管应力、位移的影响。
3) eccentricity axis sheath
偏心轴套
4) Deflect-puill
偏心衬套
5) eccentric tube
偏心套筒
1.
It is composed of collar, eccentric tube, steel-balls, piston, bolt and two holes.
这种液压自动防斜钻具主要由钻铤体、偏心套筒、钢球、阀腔、阀杆、活塞杆等组成。
6) decentralized casing
偏心套管
补充资料：在AutoCAD中偏心圆锥与偏心圆台实体的画法
现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上.
1)连接PA,PB. A(-100,0,0) B(100,0,0)
图1
在当前坐标下:
2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;
3)连接CD;
4)以CD为直径画圆;
5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;
6)过O作CD的垂线,交圆于E,F;
图2
7)用三点UCS命令,取三点为:O,P,C;
8)过点O作PO的垂线GO,交PC于G;
图3
9)再次用三点UCS命令,取三点为O,F,G;
10)现在就可以画椭圆锥了!
cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;
图4
11)回到WCS,剖切椭圆锥
SL-选择椭圆锥-回车-XY-回车-捕捉P点.
12)删除辅助线条.
图5
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条