1) end-plate
端板
1.
Finite element analysis of end-plated semi-rigid composite joints;
端板型半刚性组合节点的有限元分析
2.
Finite element analysis of bolted moment end-plate connection strength and stiffness;
梁柱端板螺栓连接强度和刚度的有限元分析
3.
A new type of bolted end-plate joint with steel beam and reinforced concrete column was developed,and two full-scale subassemblies were tested to evaluate the seismic performance of the joint details.
提出了一种新型端板高强螺栓连接的狗骨式削弱钢梁-钢筋混凝土柱节点,通过2个足尺试件的低周反复荷载试验研究了其抗震性能和破坏形态。
2) end plate
端板
1.
Direct weld applied in end plate of 800mm PHC spun pile is disadvantage with the poor soldering quality,shortage of quality measurement and negatively big impact on thermoplastic concrete zone caused by high temperature during welding.
PHC管桩尤其是800mm以上大直径端板的直焊接头存在着焊接质量差,检测焊接手段较少,而且焊接时产生的高温对热塑区的混凝土影响较大。
2.
The high strength bolted end plate connection is one type of the connections used widely in steel frame and the whole frame behavior is certainly concerned with the prying action and the thickness of the end plate.
高强度螺栓端板连接是广泛使用的刚架节点形式之一。
3) endplate
端板
1.
Based on Riley sseries test of endplate wings and Dempsey s series test of stern planes of a submarine, a new concept, theeffective aspect ratio of a wing, was put forward and then a systematic approach was developed to design thestern planes with endplates and to predict theirs hydrodynamic lift in submarine manoeuverability.
本文对Ｒｉｌｅｙ［１］机翼端板的系列试验和Ｄｅｍｐｓｅｙ［３］潜艇艉水平翼的系列试验的数据进行了重新分析，提出了稳定翼有效展弦比的概念。
2.
Secondly,given a chord length and a relative ground clearance,the wings in ground effect with different aspect ratios and endplate are simul.
首先,对给定面积和离地高度下不同展弦比的地效翼进行数值模拟;然后,对给定弦长和相对飞行高度下不同展弦比和带端板的地效翼进行数值研究。
4) end plate
端板端板
5) end plate
端板;底板
6) terminal lamella
终板;端板
补充资料：凹板印刷机用胶布板
分子式：
分子量：
CAS号：
性质：用于高速轮转凹版印刷机的胶布板。供印刷报纸、杂志、图书等。与凸版印刷机用胶布板的装置位置相同，不与油墨直接接触，但作用不同，通过橡皮表层的弹力作用，将凹沟内的油墨吸到纸张上。印刷时所受的压力较大，胶层须较厚。
分子量：
CAS号：
性质：用于高速轮转凹版印刷机的胶布板。供印刷报纸、杂志、图书等。与凸版印刷机用胶布板的装置位置相同，不与油墨直接接触，但作用不同，通过橡皮表层的弹力作用，将凹沟内的油墨吸到纸张上。印刷时所受的压力较大，胶层须较厚。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条