说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 盲孔法
1)  blind-hole method
盲孔法
1.
Analysis and experimental study on identification of inner force of steel tube under tension(compression) and bending using blind-hole method
盲孔法识别拉(压)弯钢管内力的分析与试验
2.
In order know the size and the distribution of residual stresses of mill welding seam,this paper uses blind-hole method to test the girth welds between round plate and the cylinder body of the mill produced by CBMI CONSTRUCTION CO.
为了了解滑履磨机焊缝残余应力的大小和分布规律,该文应用盲孔法对中材建设有限公司生产的某型号磨机的圆平板与圆筒体之间的环焊缝及其近缝区的表面残余应力进行了现场测试。
3.
To enhance the measurement accuracy for welding residual stress in the converter,the traditional blind-hole method is improved by widening hole and increasing depth more than once after drilling hole on one measuring point.
为提高炉体焊接残余应力测试精度,对传统的盲孔法进行改进,即在测点打孔后多次扩孔并增加孔深;通过对SM400ZL钢焊接残余应力测试时的应变释放系数A,B进行实验标定,得出多组应变释放系数值,计算可得残余应力的估算值,并对不同状况下的残余应力值进行比较。
2)  Blind hole method
盲孔法
1.
In present paper,the relationship between blind hole method and Kirsch elastic solution is discussed on the basis of solution of 3D.
通过三维弹性有限元分析和单向标定实验,分析了盲孔法与通孔解的关系,着重研究了应变释放系数A、B值,A、B值随着孔深与孔径之比(h/d)的增大而增大,当h/d>1。
2.
Phase-shift moiré interference method and blind hole method were used to measure the residual stress of composite materials.
本文应用相移云纹干涉法与盲孔法相结合检测纤维增强复合材料的残余应力。
3.
For checking the effect of runner welding and annealing of Xiaowan Hydropower Station, the residual stresses of runner before and after annealing are measured by using blind hole method and impact indentation method.
为检查小湾水电站转轮焊接、退火效果,采用了盲孔法及压痕法对转轮退火前后的残余应力进行了测试。
3)  blind-hole drilling method
盲孔法
1.
The initial residual stress of the polymer bonded explosive based on TATB and its distribution were tested by blind-hole drilling method.
以TATB基高聚物粘结炸药(PBX)为对象,采用盲孔法测定了PBX炸药的初始残余应力及其分布,研究了孔深和钻孔后应变读数时间对结果的影响,以及样品热处理后对残余应力松弛的影响。
2.
8 mm drill collar box connection from two manufacturers was measured by using blind-hole drilling method.
采用盲孔法测量直径为158。
4)  Mathar Soete drilling
钻盲孔法
1.
Distributions of residual welding stress and effect of post weld heat treatment (PWHT) on residual welding stress relaxation in Lehigh weld specimens was studied by Mathar Soete drilling.
通过钻盲孔法研究了里海型焊接试板焊接残余应力的分布和焊后热处理对焊接残余应力松弛的影响 ,讨论了适合生产实际的焊后热处理条件。
5)  testing method of superficial pits
表面盲孔测试法
6)  incremental-step blind hole drilling method
逐层盲孔钻削法
补充资料:扎盲盲
1.捉迷藏。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条