说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 填充材料
1)  filling material
填充材料
1.
Selection of welding filling material formain transformer oil tank cover of type DJ_1 locomotives;
DJ_1型机车主变压器油箱盖焊接填充材料的选择
2.
The tungsten-inert-gas(TIG) welding test on YG30 cemented carbide and the 45# steel was done with Co-Fe-C alloys in different composition as filling materials.
选用不同成分Co-Fe-C合金作为填充材料,对YG30硬质合金与45钢进行了TIG焊试验。
3.
The filling material in EDI stack is introduced in this paper.
介绍了EDI膜堆填充材料的研究现状,认为离子交换树脂仍是今后填充材料的主要研究对象,离子交换纤维和其它新型填充材料的研究亟待有新的突破。
2)  filler [英]['fɪlə(r)]  [美]['fɪlɚ]
填充材料
1.
Effect of Ti filler on microstructure and properties of joint during TIG welding for aluminum matrix composite;
铝基材料TIG焊填充材料对接头组织性能的影响
2.
In this paper,the PTFE based composites were classified reasonably into several types according to the sorts of fillers.
根据填充材料的类别不同对聚四氟乙烯基复合材料进行了合理地分类,并阐述了不同填料对聚四氟乙烯基复合材料摩擦学特性的影响,分析和比较了不同填料的减摩抗磨机理,对于聚四氟乙烯基复合材料的科学研究和工程应用具有一定的借鉴和指导意义。
3.
The traditional filling process of cabtyre cables, which uses sheathing rubber, jute rope, rubber/polypropylene strips etc as filler, is ineffective with high cost.
在橡套软电缆的填充工艺中 ,通常的填充材料是采用护套橡皮、麻绳、橡皮条和聚丙烯索等 ,但填充效果及其经济性不理想 ,本文介绍用废胶料挤包细麻绳作填充条 ,其填充效果好 ,而且成本低 ,具有较高的经济效
3)  filler material
填充材料
1.
This article analyzed the influencing factors of tungsten for automatic welding without filler materials,which including the diameter,angel,cross section of tungsten,makes a general analysis about the generation rules and influencing ways of the influencing factors.
从产生机理、影响方式等方面对不添加焊接填充材料自动化焊接中钨极的影响因素(钨极的直径、锥度大小、平台大小以及与焊件的距离)进行了综合分析。
2.
The development and application of filler material for RFPE (Reference Free Part Encapsulation) technique is introduced.
介绍了无基准零件封装夹具中填充材料的研究、试验和应用情况。
4)  Filling material
充填材料
1.
Experimental study of anti-fracture strength in endontically treated teeth by different filling materials;
充填材料对牙齿抗折裂性能影响的实验研究
2.
The experiment studied the size distribution of filling material by U9(96) uniformity design method and found an excellent size composition.
作者采用U9(96)均匀设计方法对充填材料的颗粒级配确定进行了实验研究,确立了较优的颗粒组成,在此颗粒级配下,可使充填材料获得高的堆积密度和强度;在一定固相含量条件下,可使充填材料表观粘度明显降低,具有较好的工作性能。
3.
AIM: To compare the surface roughness of three dental filling materials.
目的:比较3种牙体充填材料的表面用在粗糙度。
5)  backfill material
充填材料
1.
The newly testing and the applications of backfill materials, backfill geomechanics, paste backfill and backfill equipment are mainly introduce
综述了第七届国际充填采矿大会论文集的主要内容,着重介绍充填材料、充填体力学、膏体充填、充填设备与系统的应用现状与最新进展。
6)  backfill materials
充填材料
1.
When curing time of rapid-hardening backfill materials is up to 60 days,the weathering of the materials will begin and at 90 days the weathering becomes more severe.
高水速凝固化胶结充填材料在养护至60d左右时,开始出现风化现象,到90d时较严重。
补充资料:填充离子交换树脂的电渗析器、电渗析填充床等
分子式:
CAS号:

性质:又称填充离子交换树脂的电渗析器、电渗析填充床等。这是将离子交换树脂充填入电渗析器隔室中,将电渗析与离子交换树脂结合一起的一种脱盐方法。这种装置可以提高脱盐室的电导,并能有效地防止极化沉淀以制备高纯水。但其结构比较复杂,拆装不便。其工作原理为:将H+,OH-型阳、阴树脂予混后填充入电渗析器脱盐室。在直流电场作用下,阴、阳树脂与溶液中的阴、阳离子进行交换。之后,由于电解再生,树脂分别又转为H+,OH-型,解吸的阴、阳离子分别通过阴、阳膜进入浓缩隔室。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条