说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 虚功原理
1)  Principle of virtual work
虚功原理
1.
Stochastic principle of virtual work and stochastic finite element method for viscoelastic structural analysis;
粘弹性随机分析的虚功原理及随机有限元
2.
Based on the principle of virtual work, this paper deals with elastic plastic FEM(Finite Element Methods) of sheet metal stamping process, and then this method is introduced into related analysis processes.
虚功原理的基础上对板料冲压成形过程的弹塑性有限元分析方法进行了研究 ,并将有限变形弹塑性有限元法引入板料冲压成形过程 ,采用更新拉格朗日 (ULM ,UpdatedLagrangeMethod)方法描述 ,推导了有限元列式 ,建立了板料成形过程的有限元分析模型 ,开发了分析程序 。
3.
In the end, the average hydraulic pressure of bulging is given by the principle of virtual work.
最后运用虚功原理给出了胀形平均液压的解析解。
2)  virtual work principle
虚功原理
1.
Application of virtual work principle in Electrostatics;
虚功原理在静电学中的应用
2.
The dialectical relationship between dynamic on virtual work principle and statically balance of mechanic group;
虚功原理的动力学理论与力学组的静力学平衡
3)  the principle of virtual work
虚功原理
1.
This article intends to establish linear algebraic equations with shearing force flow asunknown quantity using the principle of virtual work.
本文应用虚功原理建立以剪力流为未知量的线性代数方程组,由此可直接解得多室闭口薄壁杆件自由扭转的剪力流。
4)  complementary virtual work principle
余虚功原理
1.
This paper applies Ritz and Galerkin method in elastic mechanics,deducts complementary virtual work principle with basic formula of elastic mechanics,and then gains minimal complementary energy principle to show that Ritz method and Galerkin method are equivalent,which illustrates that there are relative relationships between variational principle and weighted residual method.
将里茨法(Ritz)和伽辽金法(Galerkin)应用于弹性力学,由弹性力学基本方程推导出余虚功原理,进而求得最小余能原理,从而说明里茨法和伽辽金法是等价的,这也说明变分原理与加权残数法之间有亲缘关系。
5)  virtual power theory
虚功率原理
1.
Furthermore,the upper-bound solution of slope safety factor is obtained according to the theory of virtual power theory.
从极限分析原理入手,以堆积型边坡作为对象,研究了折线型滑面边坡稳定分析计算的极限分析方法,提出了折线型滑面边坡稳定系数计算的极限分析模型,并在虚功率原理的基础上推导得到了稳定系数计算的极限分析上限解。
6)  principles of virtual work and power
虚功和虚功率原理
补充资料:虚功原理
      分析静力学的重要原理,又称虚位移原理,是J.-L.拉格朗日于1764年建立的。其内容为:一个原为静止的质点系,如果约束是理想双面定常约束,则系统继续保持静止的条件是所有作用于该系统的主动力对作用点的虚位移所作的功的和为零。它的数学表达式为:
  
  
  
  
   
  
  
  
  (1)式中Fi为第i个质点上的主动力;δri为其虚位移。
  
  欲使每一个质点保持平衡,应有约束力Ni和主动力Fi成为平衡力系,即Fi+Ni=0。故对每一个质点都有Fi+Ni)·δri=0,它们的总和为:
  
  
    
  
  (2)又因约束是理想约束,故有:
  
  
  
   
  
  
  
    (3)将式(3)代入式(2),即得式(1)。
  
  将主动力F1作用于单自由度机构,必定产生一从动力F2,虚功原理即可简化为:
  
  
  
   F1δx1-F2δx2=0或
  
  
  
   F1/F2=δx2/δx1。这种作用力与位移的反比关系在机械中得到广泛应用。这就是古人早已从杠杆、滑轮、斜面等简单机械中得出的规律──"力学金律"。事实上,这种规律正是虚功原理的雏形。虚功原理的一般性表述是约翰第一·伯努利(见伯努利家族)于1717年作出的。
  
  利用虚功原理求解静力学问题,可以避免画受力图、列平衡方程等分别隔离的一套方法,而代之以求系统的各虚位移之间的几何关系。如图示的压缩机构,OC杆可绕O转动,OC杆上的滑块A带动AB杆在铅垂导槽C中滑动。在B上加一主动力P,在C产生垂直于OC的从动力Q。C点的虚位移为δc,B点的虚位移为δb。根据虚功原理便有Q·δc+P·δb=0。因δc=aδ嗞,δb=δ(AC)=δ(ltg嗞)=lsec2嗞δ嗞,所以有Qaδ嗞=Plsec2嗞δ嗞,即
  
  
  
   Q=Pl/acos2嗞。
  
  虚功原理也可应用于非理想约束的情况,此时把摩擦力也看作主动力而列入式(1)中。
  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条