1) taper tolerance
锥度偏差
1.
According to the requests of API connecting casing pole to connecting intensity and sealed capability,the paper analyzes the effect of taper tolerance of pipe external thread and coupling internal thread on using properties of casing pole.
根据API螺纹连接套管柱对连接强度和密封性能的要求,分析了管子外螺纹与接箍内螺纹的锥度偏差对套管柱使用性能的影响,提出锥度偏差应在API标准要求的基础上加以内控,将极限公差缩小至机械加工允许的范围内,是提高石油套管柱使用性能的有效途径。
2) Taper error
锥度误差
1.
This paper investigates interference distribution on tooth in different taper condition through analyzing taper error effect onconnector hand tight plane.
本文通过分析锥度误差对接头基面的影响，研究了不同锥度条件下，牙上过盈量的分布，利用弹性理论求解了接触压力的分布，进而得到装配扭矩，从理论上揭示了锥度对扭矩的影响规律，为进一步全面分析螺纹几何参数对扭矩的影响奠定了基
3) skewness bias
偏斜度偏差
4) thickness deviation
厚度偏差
1.
The effect of thickness deviation on the reflection spectra and phase shift of VCSELs has been analysed using optical transfer matrix method.
采用光学传输矩阵方法分析了厚度偏差对VCSEL的反射谱和反射相移产生的影响。
2.
For researching thickness deviation of wide heavy plate caused by bilateral stiffness difference of plate mill,rolling force distribution is analyzed by using the principle of forces and torques equilibrium and the effects of the stiffness difference of plate mill on plate thickness deviation under a variety of roll length,plate width and rolling force is studied too.
针对由于轧机两侧刚度差异引起的宽厚板两侧厚度偏差,采用力平衡和力矩平衡原理,分析了轧辊承受载荷的分布情况,研究了宽厚板两侧厚度偏差与轧辊长度、板宽、轧制力和轧机两侧刚度差异之间的规律。
3.
For researching thickness deviation of wide heavy plate caused by bilateral stiffness difference of plate mill, rolling force distribution is analyzed by using the principle of forces and torques equilibrium and the effects of the stiffness difference of plate mill on plate thickness deviation under a varity of roll length, plate width and rolling force is studied too.
针对轧机两侧刚度差异引起的宽厚板两侧厚度偏差,采用力平衡和力矩平衡原理,分析轧辊承受载荷的分布情况,研究宽厚板两侧厚度偏差与轧辊长度、板宽、轧制力和轧机两侧刚度差异之间的规律。
5) angle deviation
角度偏差
1.
Through comparing the image of the sample with the stand- ard one,the angle deviation and position deviation was obtained.
通过对摄取到的实际套准标记图像和标准图像进行比较,输出其角度偏差值和位置偏差值,以此作为自动套准控制系统中时印刷机套准调节的依据,并对一种"米"形套准标记的识别和检测进行了分析。
2.
The model with angle deviation was detail discussed, correct model could be made by exactly angle measurement.
分析了基于球杆仪的数控机床误差补偿测试原理 ,讨论了由于角度偏差引起的误差 ,指出基于球杆仪误差补偿模型的缺陷 ,提出采用该种模型必须精确测量角度
3.
Through comparing the image of the sample with the stand- ard one,the angle deviation and position deviation was obtained.
通过对摄取到的实际套准标记图像和标准图像进行比较,输出其角度偏差值和位置偏差值,以此作为自动套准控制系统中对印刷机套准调节的依据,并对一种"(?)"形套准标记的识别和检测进行了分析。
6) Deviation of roundness
圆度偏差
补充资料：锥度
1.柱形物体的横剖面向一端逐渐缩小的形式。也叫梢。 2.横剖面缩小的数值﹐如锥度1:50﹐即每长50个单位缩小一个单位。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条