说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 装夹
1)  clamping [英][klæmp]  [美][klæmp]
装夹
1.
Study on the Clamping Technology for Thin-wall Parts Processing
薄壁类零件加工装夹技术研究
2.
This thesis analyzed elastic restitution of 600MW steam turbine unit which connects with oversize flatness error , and mainly studied that gravity, clamping and m.
本文针对平面度超差问题进行分析,着重研究外缸在机加工过程中重力、装夹方式及铣削力引起的弹性恢复误差。
3.
The technical requirements of the keyway, clamping, in particular, processing methods are described in this article.
对键槽的技术要求、装夹方法特别是加工方法进行阐述,重点对键槽铣削加工经历的3个阶段包括普通铣床加工、键槽铣床加工、数控铣床和加工中心加工过程中加工刀具的选用、走刀路线的确定、加工质量的对比以及加工特点进行了分析比较。
2)  clamp [英][klæmp]  [美][klæmp]
装夹
1.
A new centering and clamp method was introduced in this text by processing of cylinder surface of pump shell.
通过泵壳在立车上径向外圆的加工,介绍了一种新型的找正、装夹方法。
2.
Make improvement aiming at the low accuracy, long time and unsteady clamp of centering turn method.
针对普通工艺所采用的找正车削法精度低、耗时长和装夹不稳固等缺点,进行工艺改进。
3.
To reflect the relationship between clamps and residual stress, finite element models with different clamping schemes were built and the clamping process was simulated.
为了揭示装夹方案对残余应力的影响 ,利用有限元技术模拟了工件加工过程中不同的装夹方案 ,并分析了模拟结果。
3)  fixing [英]['fiksiŋ]  [美]['fɪksɪŋ]
装夹
1.
But because of their poor rigidity, it is easy to bring machining deformation caused by the existence of the residual stress and the fixing stress.
残余应力及装夹应力容易使刚性差的薄壁件引起较大的加工变形,而传统工艺难以使其达到精度要求。
4)  set-up
装夹(安装)
5)  welding fixture
焊装夹具
1.
Aimed at detecting dimensional deviation in auto body assembly process of welding fixture, this paper proposes coordinate transformation model based on auto body coordinate system, and develops an real-time detection and adaptive control system using eddy current sensor and an adaptive adjustment device.
为减小汽车焊装夹具焊装过程中出现的工件尺寸偏差,提出了一种基于车身坐标系的坐标转换模型,采用电涡流传感器和设计的自适应调整装置,构建了在线检测及自适应控制系统,试验验证了这种监控报警机制及自适应调整控制系统的有效性。
6)  clamping scheme
装夹方案
1.
The clamping schemes of thinwalled package were discussed on the base of FEM analysis.
采用有限元分析方法,对薄壁件的装夹方案进行了讨论。
2.
The result indicates, the clamping scheme with six points is more effective and their position is also given.
针对薄壁结构件刚性差,加工中易变形的工艺难题,运用ANSYS结构静力学分析和正交优化分析的方法,模拟了夹紧点个数、夹紧点位置对加工中工件受力变形的影响,对装夹方案进行了优选。
3.
In this paper,finite element models are established to analyze the milling deformation of multi-frame components caused by different multi-point clamping schemes.
目前,国内外对装夹方案的研究局限于单框的装夹效应的研究,没有分析装夹方案对多框体铣削加工变形的影响。
补充资料:铠装夹布胶管
分子式:
分子量:
CAS号:

性质:见夹布胶管。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条