1) sandblast cylinder
喷砂罐
1.
Combining the parametric design and finite element structural analysis by the parametric design language(APDL) in ANSYS software,we have constructed the finite element model of the sandblast cylinder.
利用ANSYS软件中参数化设计语言(APDL),将参数化设计与有限元结构分析相结合,建立了喷砂罐的有限元模型。
2) sand hopper
喷砂砂罐
3) spray tin
喷罐
4) sand blasting
喷砂
1.
Substrate preteatment technique sand blasting exists two big problems recently:(1) sand material not being able utilized cyclically, technological cost being high,resources waste being serious;(2) dust control method being single,effect of dust removal being bad,environmental pollution and its effect on human health being serious.
针对基体前处理技术中的喷砂存在的两大问题:1)砂料不能循环利用,工艺成本高,资源浪费严重;2)粉尘控制方法单一,除尘效果不良,环境污染严重,影响人体健康。
2.
In order to improve working environment of hard alloy for mine,replacement of sand blasting by ball milling handling technology is put forward.
对矿用硬质合金的热处理和时效处理 ,通常采用喷砂工艺 ,为改善劳动环境 ,提出球磨处理技术取代喷砂 ,取得了明显的技术经济效
3.
Also several methods of fabricating the barrier ribs and the advantages of applying sand blasting to fabricate the barrier ribs are presented.
简要介绍了障壁制作在彩色 PDP中的重要性 ,障壁制作的几种方法及喷砂法制作障壁的优点。
5) sandblasting
[英]['sændblɑ:st] [美]['sænd,blæst]
喷砂
1.
The Effect of Sandblasting on the Band Strength between Enamel and Bracket;
喷砂技术对牙釉质和正畸托槽间黏结强度的影响
2.
This article introduces the properties of resist sandblasting UV ink and its application.
介绍了用于精细喷砂工艺的UV网印抗喷砂油墨、水显影感光抗喷砂油墨、抗喷砂水转印纸的特性、使用范围、工艺流程、注意事项、问题与对策等,并与其他类型的抗喷砂油墨和市售抗感光喷砂胶片进行了对比。
3.
After compared themethod ofsurfacetreatmentbeforeprotectivecoating ofsteelstructures and equipments, in petrochemical industry,including dry and wet sandblasting,phosphating,acid cleaning,hand and powertoolrust-remoral, high pressure abrasivewaterjetrust-removal.
从石化企业实际出发,对钢结构与设备防腐涂装前表面清理方法进行对比,包括干喷砂、湿喷砂、磷化、酸洗、手工与动力工具除锈、高压磨料水射流清洗等清洗方法,从中提出如何合理地选择清理方法。
6) Grit blasting
喷砂
1.
The mathematical model which characterizes the relationship among parameters of grit blasting, i.
应用二次旋转组合试验进行试验设计 ,建立了喷砂距离、喷砂压力、喷砂角度与涂层和基体间结合强度的数学模型。
2.
As a conventional surface process,grit blasting can be used to clean and roughen metal surface.
喷砂是常用的金属表面处理方法,可起毛化和清洁作用,如作为热喷涂涂层的预处理工艺。
补充资料：砂罐
1.陶质器皿。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条