1) Coating
[英]['kəʊtɪŋ] [美]['kotɪŋ]
镀层
1.
Effects of temperature and coatings on wettability of Sn-Cu-Ni lead-free solder;
温度与镀层对Sn-Cu-Ni无铅钎料润湿性能的影响
2.
Determination of metal ions by capillary electrophoresis in coating;
毛细管电泳法测定镀层中金属元素
3.
Relationship between the Distribution of Coating and the Orientation of Cathode in Composite Coating;
复合镀中镀层分布与阴极位向的关系
2) plating
[英]['pleɪtɪŋ] [美]['pletɪŋ]
镀层
1.
Effect of plating on adhesion property between steel cord and rubber;
镀层对钢丝帘线与橡胶粘合性能的影响
2.
Research of accelerated corrosion test method of zinc, cadmium plating on high-strength steel;
高强度钢锌、镉镀层加速腐蚀试验方法研究
3.
Determination of Plating or Coating Thickness by Isotopic X_Ray Fluorescence Spectrometry;
工业镀层及涂层厚度分析——同位素X射线荧光光谱法
3) coatings
镀层
1.
Effects of temperature and coatings on wettability of Sn-Ag-Cu lead-free solder;
温度与镀层对Sn-Ag-Cu无铅钎料润湿性的影响
2.
Technical conditions of Ni-P-(Ni/SiC)_P coatings;
Ni-P-(Ni/SiC)_P镀层及其工艺条件的研究
3.
This paper first predicted the possibility of TiB2 formation in Ti-B-C system, and then focused on the preparation of TiB2 coatings by electroplating on the graphite in fluoride-chloride electrolytes (KF-KCl) containing K2TiF6 and KBF4 as the electrochemically-active components.
本研究首先通过热力学分析验证了在Ti-B-C体系生成TiB2的可能性,然后在K2TiF6和KBF4作为活性物质的KF-KCl熔体中以石墨为基体通过直流电沉积(CCP)和周期断开电流电沉积(PIC)技术制备了TiB2镀层,并且研究了电流密度和电镀技术对镀层表面平整度、致密度和晶粒尺寸的影响。
4) Coat
[英][kəʊt] [美][kot]
镀层
1.
Experiment of Compound Coating with(Ni/SiC)_P as Second Phase Particle;
(Ni/SiC)_P为第二相粒子的复合镀层研究
2.
To introduce the determination of rare earth content in Zn-Al-RE alloy coat using the C 24 H 18 ClN 4O 12 PS 2-m A spectrophotometry.
介绍用偶氮氯膦—mA分光光度法测定锌 -铝 -稀土合金镀层中的稀土量。
3.
It is shown by test that adding minute quantity Al to pure Zn coating liquid can make the surface of coated steel wire appear silvering,adding about 0.
2 %Al能抑制钢丝镀层Fe -Zn合金层的生长 ;适用于通常热镀锌工艺条件的Al含量以 0 。
5) plating layer
镀层
1.
In this paper,a magnetoresistance sensor with difference structure is designed,so the problem of small signal and large disturbance in the magnetic leakage testing for the parts with plating layer is solved.
针对镀层工件漏磁检测中检测信号微弱,干扰信号相对于缺陷信号大等特点,采用具有差分结构的磁阻传感器设计,对传感器信号进行放大、滤波处理,对传感器进行置复位、增益和偏差调整电路设计,取得了满意效果。
2.
Polarization curves show that the Ni-P plating layer has long passivation district and better corrosion resistance in the 3.
研究了压铸镁合金AZ91的表面化学镀镍磷合金的工艺,利用X射线衍射(XRD)、扫描电镜(SEM)、能谱(XPS)及极化曲线的测量等方法,探讨了镁合金表面化学镀Ni-P层的组织、相、成分及其耐蚀性,结果显示,镁合金化学镀Ni-P合金镀层在350℃热处理后成晶态,镀层成分为NiP、Ni2P等。
3.
One technological problem about the weak combination of interface between Cr plating layer and substrate which was strengthened by plasma had been put forward according to the application state of under serious ablation and erosion by hot chemical airflow.
针对高温化学气流冲刷烧蚀的使用状态,提出了等离子束流界面强化解决镀Cr层与基体结合强度不足的技术问题,用非转移等离子束流对镀铬钢件表面进行快速加热进行界面强化处理的工艺方法,介绍了等离子束流界面强化原理,进行了等离子束流强化工艺试验,并对试验结果进行了检测和分析研究,结果表明,镀Cr层与基体产生了冶金结合,较为显著地提高了镀层与基体的结合强度。
补充资料：镀层
镀在其他金属或物体表面上的金属薄层。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条