1) equal-cross section lateral extrusion
等径侧向挤压
1.
According to the moving direction relations between punch and workpiece,a new definition of lateral extrusion has been put forward,at the same time,the new concepts of compressing lateral extrusion,equal-cross section lateral extrusion and stretching lateral extrusion have been put forward too.
根据挤压方向和挤出方向之间的相互关系,对侧向挤压这一概念赋予了新的定义,同时也提出了扩径侧向挤压、等径侧向挤压和缩径侧向挤压3个新概念,进一步给出了等径侧向挤压真应变的计算公式,并指出等径侧向挤压法是制备块状细晶材料的一种好方法。
2.
In this paper,the strain of the equal-cross section lateral extrusion has been analyzed,and the true strain and equivalent true strain formulae are derived from the strain analysis of the plane-pureshear deformation.
对等径侧向挤压变形的应变进行了深入的分析，应用平面纯剪切变形应变分析的结果，得到了等径侧向挤压变形真应变和等效真应变的计算公式，分析了循环等径s型侧向挤压真应变和等效真应变的变化规律。
2) equal cross section lateral extrusion
等径侧向挤压
1.
Finite element analysis of deformation uniformity of equal cross section lateral extrusion;
等径侧向挤压变形均匀程度的有限元分析
2.
In this paper,the curves of load verses displacement during equal cross section lateral extrusion process have been measured and calculated by FEM respectively,the calculated results are in good accordance with the measured results.
本文对等径侧向挤压过程中载荷的变化， 分别进行了实测及有限元模拟计算， 两种结果吻合较好。
3) equal-channel angular pressing (ECAP)
侧向等径挤压(ECAP)
4) compressing lateral extrusion
扩径侧向挤压
1.
According to the moving direction relations between punch and workpiece,a new definition of lateral extrusion has been put forward,at the same time,the new concepts of compressing lateral extrusion,equal-cross section lateral extrusion and stretching lateral extrusion have been put forward too.
根据挤压方向和挤出方向之间的相互关系,对侧向挤压这一概念赋予了新的定义,同时也提出了扩径侧向挤压、等径侧向挤压和缩径侧向挤压3个新概念,进一步给出了等径侧向挤压真应变的计算公式,并指出等径侧向挤压法是制备块状细晶材料的一种好方法。
5) stretching lateral extrusion
缩径侧向挤压
1.
According to the moving direction relations between punch and workpiece,a new definition of lateral extrusion has been put forward,at the same time,the new concepts of compressing lateral extrusion,equal-cross section lateral extrusion and stretching lateral extrusion have been put forward too.
根据挤压方向和挤出方向之间的相互关系,对侧向挤压这一概念赋予了新的定义,同时也提出了扩径侧向挤压、等径侧向挤压和缩径侧向挤压3个新概念,进一步给出了等径侧向挤压真应变的计算公式,并指出等径侧向挤压法是制备块状细晶材料的一种好方法。
6) lateral extrusion
侧向挤压
1.
The classification of the extrusion methods and the characterizes of lateral extrusion;
挤压方法的分类及侧向挤压的特点分析
2.
A rigid-plastic element-free Galerkin-finite element(EFG-FE) coupling method was developed for the numerical simulation of plane lateral extrusion process.
应用刚塑性耦合无网格-有限元法,对平面侧向挤压过程进行数值模拟。
补充资料：侧向挤压
侧向挤压
sideway extrusion
CeXIQng』lyo侧向挤压(sideway extrusion)制品流出方向与挤压杆运动方向成900的挤压方法，也称横向挤压。可分为单向侧向挤压和双向侧向挤压(如图所示)。侧向挤压的特点是:挤压模与锭坯轴线成9扩放置，挤压力与锭坯轴线方向一致，这种金属流动机构使制品遍纂 。b今簿黔 侧向挤压示意图 a、乙单向侧向挤压;‘一双向侧向挤压 1一挤压筒;2一挤压杆;3一模子;4一锭坯;5一挤压制品的纵向力学性能差异最小;变形程度大，挤压比可达100:1，制品强度高;要求模具和工具具有高的强度及刚度。该方法被用来制造高质量的航空用阀的弹簧。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条