1) electric contact
电接触
1.
Studies on electric contact silver based composite deposit intensified with nano crystal diamond particles;
纳米晶金刚石织构粒子增强银基电接触复合镀层的研究
2.
Study on the electric contact and surface film of electric machines;
电机的电接触及表面膜研究
3.
Analysis of cathode voltage drop in aluminum electrolysis cells with an electric contact model;
采用电接触模型的铝电解槽阴极电压降分析
2) electrical contact
电接触
1.
Application of electroplated silver alloy/nanoparticle composites to electrical contact of high-voltage switch
纳米粉体复合镀银合金在高压开关电接触部位上的应用
2.
So far, fretting induced failures in electrical contact is an important subject, but has not been paid much attention in experimental investigations.
以AgCu10合金为对象 ,研究和探讨了离子注入提高电接触材料的抗氧化和抗磨损性能并改善电接触微动磨损的技术。
3.
Based on the developmental procedure of electrical contact theory,several popular problems on electrical contact theory at home and abroad is analyzed according to the situation of coal production in this paper.
根据电接触理论的发展过程，并结合煤矿生产现状对目前国内外电接触可靠性研究中的几个热点问题进行了分析。
3) contact resistance
接触电阻
1.
Stable distribution analysis to statistical evaluation of contact resistance in aluminum alloy spot welding;
基于稳定分布的铝合金点焊接触电阻
2.
On the contact resistance between graphite/polypropylene composite plate and carbon paper;
石墨／聚丙烯复合板与碳纸间的接触电阻
3.
Study of prediction method for contact resistance based on experiment constitutive relation;
基于实验本构关系的接触电阻预测方法研究
4) interfacial contact resistance
接触电阻
1.
The electrochemical methods were investigated in a simulated PEMFC environment and the volt-ampere technique was applied to measure interfacial contact resistance between the sample and carbon paper.
以304不锈钢为研究对象,采用电化学方法测定其在模拟PEMFC环境下的极化曲线和对应于PEMFC工作电位下的恒电流极化曲线,用伏安法测量304不锈钢表面氧化膜/钝化膜与碳纸之间的接触电阻。
2.
The 304 stainless steel treated by electroplating Cr and plasma-assisted nitriding processes was investigated by electrochemical methods in the simulated PEMFC environments, and interfacial contact resistance between the samp.
测定了经过镀铬后再离子氮化的304不锈钢在模拟PEMFC环境下的电化学性能,测量了氮化层与碳纸之间的接触电阻。
3.
The interfacial contact resistance between the sample and carbon paper are measured with volt-ampere technique.
以304不锈钢做为研究对象,测定了其在模拟PEMFC环境下的极化曲线,极化时间分别为4 h和10 h的交流阻抗谱,用伏安法测量了304不锈钢表面氧化膜/钝化膜与碳纸之间的接触电阻。
5) contact potential
接触电势
1.
Discussion on contact potential of a semiconductor pn junction;
对半导体pn结接触电势的一个讨论
2.
This paper studies and analyses the key factors which induce fluctuation of corrosion data measured by electrical resistance probe based on principle of temperature compensation,and it was found that the main factos are contact potential between different metals and differential temperature potential due to the temperature drift.
基于温度补偿的原理,对引起电阻探针腐蚀监测数据波动的关键因素进行了大量研究和分析,发现异种金属间的接触电势和温差电势差,是造成测量数据温度漂移的主要原因。
3.
A new formula for calculating contact potential of level-ground grids(published in No.
文献１所提出的水平地网接触电势新公式在使用上仍有所不便。
6) Touch current
接触电流
1.
In order to uniform the terms among different standards,it is suggested to rename the term leakage current in clause 13 to touch current in next amendment of standard.
考虑到不同标准之间术语的一致性,建议相关的标准技术委员会在修订标准时将第13章的泄漏电流(leakage current)改称为接触电流(touch current)。
2.
Based on studing the reason why the touch current of the electronic equipment exist and why it′s value exceed 3.
文章从接触电流成因、导致接触电流偏大的因素等2个方面对接触电流偏大的原因进行了理论分析,结合某电子设备的实例详细论述了该问题的解决过程,并最终给出了切实可行的整改措施,提供了相关问题的解决途径。
补充资料：电接触烧伤
电接触烧伤
electric contact burn
电流通过人体引起的局部性和全身性的损伤，称
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条