说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 树脂液相浸渍
1)  resin liquid-phase impregnation
树脂液相浸渍
2)  impregnated resin
浸渍树脂
1.
The characteristics of five different phosphinic(phosphoric)impregnated resins adsorbing heavy rare earth elements in hydrochloric acid are studied by static method.
利用静态法研究了5种不同膦(磷)类萃取剂的浸渍树脂在盐酸介质中对重稀土的吸附行为。
2.
The adsorption and elution of thulium,ytterbium and lutetium rich material were studied by cooperative extraction chromatography with Cyanex272-P507 impregnated resin,including the influence of concentrations of stripping agents,the load of Tm-Yb-Lu rich material,effluent velocity and temperature on eluting Tm-Yb-Lu.
以Cyanex272-P507浸渍树脂采用萃取色层法对铥镱镥富集物进行了吸附和淋洗分离研究,考察了淋洗剂浓度、稀土负载量、淋洗液流速等因素对分离铥镱镥富集物的影响。
3.
The TPPS4 impregnated resin was prepared by loading meso-tetra-(4-sulfophenyl)porphine (TPPS4) onto a macro-porous adsorption resin 1300-Ⅱ.
本文用meso-四(4-碳酸苯基)卟啉处理1300-Ⅱ型大孔吸附树脂制得县有相应卟啉基团的浸渍树脂(TPPS4浸渍树脂),并用静态法求得TPPS4浸渍树脂吸附镉的最佳pH,平衡速率、吸附容量、吸附物组成及热力学函数等。
3)  Resin impregnation
树脂浸渍
1.
Resin impregnation was used to densify carbon fiber preforms after they had been densified by chemical vapor deposition (CVD).
 将炭纤维坯体CVD增密至不同密度,再对其进行树脂浸渍。
2.
85g/cm 3 by resin impregnation after pre-densification to different initial densities by CVD(chemical vapour deposition).
将CVD预增密至不同初始密度的C/C复合材料进行树脂浸渍 /炭化补充增密至 1 85 g/cm3,热处理后进行热物理性能的检测和不同刹车压力的摩擦磨损试验。
4)  impregnating resin
浸渍树脂
1.
Vacuum foaming behaviour and test method of foaming vacuity of an impregnating resin;
浸渍树脂的真空沫化特性及其沫化真空度试验方法
2.
Research progress of impregnating resin used in automobile filter paper;
汽车滤纸浸渍树脂研究进展
3.
The compositing route,manufacturing process,routine performances and ageing tests of H9110unsaturated polyester-imide impregnating resin are introduced.
通过优化分子结构和封端技术制备了H9110不饱和聚酯亚胺无溶剂浸渍树脂 ,研究了合成路线、制造工艺、常规性能和老化试验 ,并将其与国内外同类产品进行综合比较 ;结果表明 ,该浸渍树脂低温快固化、成本较低、性能良好 ,能够满足高压电机少胶云母带配套VPI绝缘结构的性能及工艺要求。
5)  liquid impregnation
液相浸渍
1.
The procedure of liquid impregnation is one of the important procedures of preparing carbon/carbon(C/C) composites.
液相浸渍工艺是制备C/C复合材料的重要工艺之一,本论文采用CVD和液相浸渍工艺制备了C/C复合材料,并对其力学性能、导热系数、摩擦磨损等性能进行了检测和分析,研究了材料工艺—结构—性能的相互关系。
2.
The principles and characteristics of the four densification methods for C/C composites were introcuced,including chemical vapour infiltration(CVI),liquid impregnation,CVI+liquid impregnation and chemical liquid vapour infiltration.
综合论述了化学气相渗透(CVI)、液相浸渍、CVI+液相浸渍和化学液气相渗透等4种增密碳纤维增强碳基(C/C)复合材料方法的原理和它们的特点。
6)  Cyanex272 impregnated resin
Cyanex272浸渍树脂
1.
The influence of separating thulium-ytterbium-lutetium-rich material and parameter of chromatography column were studied by extraction chromatography with Cyanex272 impregnated resin,including temperature,column rations,the acid concentrations in eluting,loading of rare earths and flow rates.
研究了不同温度、淋洗液酸度、稀土负载量、淋洗液流速及装柱树脂高度对Cyanex272浸渍树脂萃取色层法分离Tm,Yb,Lu的影响和柱参数。
补充资料:浸渍树脂
分子式:
CAS号:

性质:见溶剂浸渍树脂

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条