1) cold-bending forming
冷弯变形
1.
,Ltd by breaking through traditional cold-bending forming change on OD 114 mm high frequency welded pipe units.
上海申花钢管有限公司在114高频焊管机组上突破传统冷弯变形方法,设计出强力焊管。
2) cold roll forming
冷弯成形
1.
In this paper, the theoretical approaches on simulation of cold roll forming are classified into four types: simplified analytic method & kinematics method, energy method, finite strip method, and finite element method.
辊式冷弯成形是一项具有显著经济效益和社会效益的板加工工艺 ,它又是一个涉及诸多因素的复杂的工艺过程 ,对其进行计算机仿真研究是十分必要的 。
3) cold forming
冷成形冷弯
4) bending deformation
弯曲变形
1.
Numerical simulation of the bending deformation of a casing;
井下套管弯曲变形的数值模拟
2.
Calculation of bending deformation of beam(plate) considering geometric nonlinearity;
考虑几何非线性时梁(板)的弯曲变形计算
3.
The bending deformation of the aspherical bending lapping tool under the action of bending moment was analyzed according to its deformation feature in high speed lapping process.
针对高速研磨加工中使用的弯曲成型法非球面磨具的变形特点,分析了磨具在弯矩作用下产生的弯曲变形,指出磨具高度对磨具成形误差影响较大,磨具宽度对其影响较小。
5) bending deflection
弯曲变形
1.
The paper comprehensive study three respects: the influence upon bending deflection caused by three primary aspects such as gravity,pull of the mouth of well and rotate speed of drillstring.
综合考虑了钻柱的重力、井口部的提升力及钻柱的转速等三个主要方面对钻柱弯曲变形的影响,建立了动力学模型和方程,并以实例验证了本研究方法的可靠性。
2.
For resolving the problem of bending deflection of overhang shaft,it is macroprogram that is applied to compensate the errors of machining deflection timely.
为了解决悬伸轴较大的弯曲变形问题,应用宏程序编程适时补偿切削变形误差,从而获得较高的加工精度,并能提高效率,降低成本,达到了预期的目的。
3.
The calculation of bending deflection is always required in analyzing stiffness of the continual beams.
工程实际中,常采用各种形式的连续梁,对连续梁进行刚度分析时,需要计算其弯曲变形。
6) deformation
[英][,di:fɔ:'meɪʃn] [美]['difɔr'meʃən]
弯曲变形
1.
A study on bend deformation equation of ring elastic slice and solution;
环形弹性阀片弯曲变形曲面方程及其解
2.
Several ways to reduce deformation are proposed.
分析了 YG6长条薄片生产过程中弯曲变形的影响因素 ,提出了几种抑制弯曲变形的方法。
3.
Based on the mechanics model of ring throttle slice of telescopic shock absorber on a linear pressure, by the boundary constraint and deformation continuity condition, the general solution of differential equation of throttle slice deformation was got, and with mathematical transform, the analytic formula of throttle slice deformation was established.
根据减振器环形节流阀片线性非均布力学模型,利用节流阀片的边界约束条件和连续性条件,得到环形阀片弯曲变形曲面微分方程的通解,然后通过恒等变换,建立了环形节流阀片在线性非均布载荷作用下的弯曲变形系数和弯曲变形解析计算式。
补充资料：胎圈变形、弯钢圈、钢圈变形、口弯等
分子式：
CAS号：
性质：又称胎圈变形、弯钢圈、钢圈变形、口弯等。指轮胎胎圈表面局部高低不平的现象。 胎圈底部 bead base 又称胎圈基部。指轮胎与轮辋胎圈座接触的部位。其作用是保持胎圈与轮辋底部相着合。
CAS号：
性质：又称胎圈变形、弯钢圈、钢圈变形、口弯等。指轮胎胎圈表面局部高低不平的现象。 胎圈底部 bead base 又称胎圈基部。指轮胎与轮辋胎圈座接触的部位。其作用是保持胎圈与轮辋底部相着合。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条