说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 气流雾化
1)  gas atomization
气流雾化
1.
The instability theory of fluid flow is applied in gas atomization and the results show that the instability of interfacial wave is the main cause of gas atomization.
运用流动稳定性理论研究气流雾化的机理问题并与有关实验进行比较,证明了界面波失稳引起的不稳定波增长是喷射雾化中液滴形成的主要原因· 另外本文还研究了液滴粒径随各参数的变化规律,理论和实验的结果在一定程度上是符合的,因而它将对喷射成形工艺的研究起到一定的指导作
2)  multi-stream gas atomization
多流气雾化
1.
Through orthogonal experiment,systematic study is made of the influence of upper bed/lower-bed gas temperature,metallic melt temperature and catheter projecting height on the average particle size and particle distribution of the powder prepared by multi-stream gas atomization.
采用正交实验方法系统地研究了上层气流压力、下层气流压力、金属熔液温度、导液管突出高度对多流气雾化法工艺所制备粉末的平均粒径及粒度分布的影响,通过直观分析和方差分析,评价了各参数对粉末粒度的显著程度,优化了多流气雾化粉末制备法的工艺参数。
3)  air-blast atomization
气流式雾化
1.
During the coaxial air-blast atomization process, small initial disturbances were amplified after a certain length (called an undisturbed length,L_u) and evolved into unstable waves eventually, which could be observed on the surface of the liquid jet.
对同轴双通道气流式雾化喷嘴的初次雾化过程进行了实验研究,发现在初次雾化过程中,初始微小扰动经过一段距离(即未扰动长度)后,在液体射流表面发展成为可以观察到的不稳定波。
4)  airstream atomizer
气流雾化法
5)  air-flowing type atomizer
气流雾化器
1.
Afterwards, the air-flowing type atomizer is chosen as the experiment object for the practical application.
在实验研究过程中,以油雾粒径为衡量油雾发生器雾化效果的重要指标,并选择压缩空气压力和针阀与喷孔的距离为气流雾化器雾化效果的最主要的影响因素。
6)  two-fluid nozzle
气流雾化喷嘴
1.
The experiments showed that the two-fluid nozzle can be mounted at the bottom or the lateral wall of the bed for powder granulation or coating.
气流雾化喷嘴是喷动流化造粒装置的主要部件。
补充资料:气流式雾化器
分子式:
CAS号:

性质:又称气动喷嘴。它是利用压缩空气使料液在喷嘴出口处相遇而产生液膜分列并雾化。由于料液速度不大,而气流速度很高,两种流体存在着相当高的相对速度,液膜被拉成丝状,然后分裂成细小的雾滴。雾滴的大小取决于气体的喷射速度、料液和气体的物理性质、雾化器的几何尺寸以及气液量之比。气液量之比越大,则雾滴越细越均匀。主要优点雾滴粒径小且较为均匀,一般为10~60μm;能处理高黏度的料液。主要缺点:喷嘴效率低,压缩空气费用较高。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条