说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 连续挤压模
1)  continuous extruding die
连续挤压模
2)  continuous extrusion
连续挤压
1.
Deformation model and stress distribution of continuous extrusion process;
连续挤压变形力学模型与接触应力分布规律
2.
Numerical simulation of temperature field of copper flat wire continuous extrusion forming;
铜扁线连续挤压过程温度场的数值模拟
3.
Analysis of temperature in copper continuous extrusion process;
铜连续挤压工艺过程中的温度分析
3)  continuous extrusion forming
连续挤压
1.
Computer simulation of continuous extrusion forming process;
连续挤压成形过程的计算机仿真
2.
Using DEFORM-3D software and the rigid viscoplastic FE(finite element) theory,we study in some depth the effects of different spread outlets of a shoe on the continuous extrusion forming process of flat copper wire.
基于DEFORM3D软件,采用刚粘塑性有限元理论,运用三维有限元技术详细研究了不同靴座扩展出口宽度对铜扁线连续挤压成形过程的影响。
3.
The effects of the hindrance angles on continuous extrusion forming of the big flakiness copper flat wire are investigated by three-dimensional finite-element technology based on software DEFORM-3D.
基于DEFORM3D软件,采用刚粘塑性有限元理论,运用三维有限元技术详细研究不同阻碍角对铜扁线连续挤压成形过程的影响。
4)  conform [英][kən'fɔ:m]  [美][kən'fɔrm]
连续挤压
1.
A Pressure Balance Criterion of Die Cavity Design in Cable Al Sheath CONFORM Cladding;
电缆铝护套连续挤压包覆型腔设计的均压判定准则
2.
Development of Management Information System in Research Center of CONFORM Engineering;
连续挤压工程研究中心管理信息系统的开发
3.
It provides theoretical basis for determining geometric Parameters of bonding container and designing die of conform.
从模具型腔结构特点上探讨了连续挤压制件裂纹产生的原因,利用主应力法和滑移法对焊合室内变形金属的应力进行了分析,为确定合理的连续挤压型腔几何参数和模具设计提供了一定的理论依据。
5)  CONFORM continuous extrusion
Conform连续挤压
1.
The study on aluminium alloy coil tube production process reveal that Conform continuous extrusion is the new technology for producing aluminium alloy coil tubes in automobile air conditioners.
采用Conform连续挤压技术研制汽车空调器用铝合金盘管,获得生产汽车空调器用铝合金盘管的最新生产工艺。
6)  continuous extrusion
连续挤压机
1.
Structural analysis and improvement on the foundation of TLJ400 continuous extrusion;
TLJ400连续挤压机底座的结构分析与改进设计
补充资料:导流模挤压


导流模挤压
diversion die extrusion

dooliumu Jiyo导流模挤压(diversion die extrusion)在不带独立穿孔系统的挤压机上,采用导流模使实心锭坯在挤压力作用下发生金属塑性变形的挤压方法。导流模即表面改设适当的导流孔的挤压模或者在挤压模前面增设开有导流孔的导流板。 导流模挤压的原理是:把金属直接作用在模具上所产生的突变载荷,通过导流孔的续流作用改变为梯度平缓的载荷,调整金属充填速度和孔型各部分的制品出口速度,使金属连续平稳地通过模孔(如图所示)。 左工二\愿撤积勇,_A {111{了l\\\\减丫又矛矿又卜;、习B一B 。生,一一一-‘众、-一眠七d//,勺曰吮Ji 11、叶下尸\\通B:毛非」‘臀几 b 导流模示意图 一带导流板的导流模;卜一~带焊合室的导流模 l一导流板,2一导流模;3一模垫 导流模挤压的特点是:(1)导流孔具有对金属充填比例进行预分配的功能,因而无论对于空心型材,半空心型材及薄壁实心型材都适用,特别是对于宽厚比比较大的型材、模孔形状易被堵损的模具更有实用价值。(2)若将导流板做成5“的锥角,可防止切残料时将导流板孔腔中的残余金属被残料拖出。这样在前一根制品挤出后,导流板孔腔内残留下的金属可以和下一根金属前端焊合在一起,从而实现连续挤压,进而保证实现完全的牵引挤压。〔3)提高成品率,缩短挤压周期。 导流模不论在平模挤压或是组合模挤压时都适用。在组合模中常将导流板与模子做成一个整体,形成凹腔或焊合室。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条