1) microstructure
[英]['maikrəu,strʌktʃə] [美]['maɪkro,strʌktʃɚ]
微组织
1.
The microstructure、phase structure of the alloy have been observed by the use of the optical micrography and TEM.
利用光学显微镜及透射电镜分析了Al-Cu合金铸态和热处理态的显微组织、相组成及分布。
2) microstructure
[英]['maikrəu,strʌktʃə] [美]['maɪkro,strʌktʃɚ]
微观组织
1.
Acicular ferrite microstructure of weld metal for low-alloy steel;
低合金钢焊缝的针状铁素体微观组织
2.
Effects of Ce and Sn on Microstructure of AZ91 Magnesium Alloy;
Ce、Sn对AZ91合金微观组织的影响
3.
Preorm optimal design and experimental study on the microstructure in forging process;
面向微观组织优化的锻造工艺预成形优化设计及实验研究
3) Microstructures
微观组织
1.
Effect of strain rate on flow stresses and microstructures of titanium alloy TC11 alloy;
应变速率对TC11钛合金流动应力和微观组织的影响
2.
Effects of minor manganese addition on microstructures and tensile properties of Al-Mg-Si alloys;
微量Mn对Al-Mg-Si合金微观组织与拉伸性能的影响
3.
Mechanical properties,microstructures and fracture appearance of the sand-cast samples of ZL210A alloy solution-treated at 545 ℃ and 555 ℃ respectively were analyzed.
通过对ZL210A合金砂型试样进行545℃固溶和555℃固溶处理,分析不同固溶温度处理试样的力学性能、微观组织和断口形貌,探讨了不同固溶温度对合金砂型试样性能和组织的影响。
4) microscopic structure
显微组织
1.
The influence of rotating magnetic field on the microscopic structure of welded metal by laser welding;
旋转磁场对激光焊缝金属显微组织的影响
2.
The microscopic structure of the plane-spring made of 60si2Mn steel after the fatigue crack is observed and analyzed with mettaloscope.
通过金相显微镜对60Si2Mn钢制汽车板簧疲劳损坏的过程进行显微组织分析,研究了疲劳裂纹萌生的位置、扩展过程和扩展途径,探索提高汽车板簧疲劳寿命的有效方法。
3.
The results show that the joint with good microscopic structure and mechanical property can be obtained by using optimized welding process parameters and rational heat treating process after welding.
对 45钢 /W8Co3N高速钢刀具的摩擦焊接工艺及焊接效果进行了试验研究 ,结果表明 ,采用优化的摩擦焊接工艺参数及合理的焊后热处理工艺可获得具有良好显微组织和力学性能的焊接接头。
5) micro-structure
显微组织
1.
With the help of metal graphic microscope,micro-structure of different section of weld.
借助金相显微镜,观察分析了不同冷却速度下的显微组织和焊接接头不同部位的显微组织。
2.
, the chemical composition, manufacturing process, micro-structure, strenthening mechanism, properties, applications, grades and specifications.
全面地描述了非调质钢的发展概况，分析了非调质钢发展过程中化学成分、加工工艺、显微组织、强化机制、性能、应用范围、品种规格等方面特征的变化。
6) micro structure
微观组织
1.
The tests on the micro structure and mechanical performance of Incoloy 800H alloy which has been in high-temperature and high-pressure environment service of H_2-presence for 100,000 hours and comparison of the test results with characteristics of hydrogen induced cracking of austenitic steel ha.
文章通过试验研究了高温高压临氢环境下、服役约100 kh的Incoloy 800H合金钢的微观组织和力学性能,并将试验结果与氢致奥氏体不锈钢损伤典型特征比较,发现长期服役在高温高压临氢工况下,氢致Incoloy 800H力学性能下降和微观组织损伤轻微,即Incoloy 800H合金钢抗氢损伤性能优良。
2.
The influence to micro structure of laser cladding layer by laser cladding craft parameters is studied, and the micro hardness of laser cladding layer and substrate is tested.
研究了工艺参数对激光熔覆层微观组织的影响,测试了熔覆层和基材的显微硬度,获得了无裂纹、孔洞等缺陷的熔覆层。
补充资料：微波组织凝固治疗
微波组织凝固治疗
介入放射学技术。利用特殊设计的一套微波电极针行肿瘤治疗的方法。局麻下，通过导向穿刺针经皮穿入肿瘤内。使用能发射2450MHz微波的组织凝固器，以60W的功率发射60秒，可多次穿刺肿块的不同部位行微波治疗，直至超声监视到整个肿瘤内均呈高回声为止。可于同一部位多次实施。微波能使局部组织不断升温发热而周围组织则不被升温。即其仅仅消融局部肿瘤组织而不影响周围正常组织。微波同时兼有止血功能，是一种很安全的技术。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条