1) steel matrix
钢基体
1.
A variety of experiment techniques were used to investigate the interactions between tungsten carbide particle and the steel matrix.
用电冶熔铸工艺制备不同WC含量的WC/钢复合材料,研究了WC颗粒在复合材料钢基体中的溶解行为和影响因素。
2.
In this paper the author had introduced the development and situation of steelbonded hard alloy from the study of steel matrix,hard phase and procedure.
耐磨钢结材料由于其广泛的工艺特性和良好的综合物理机械性能及优异的化学稳定性而被应用于工业生产各个领域,本文从钢基体的研究、硬质相的种类及特点、工艺概述三方面介绍了其研究进展及现状。
2) steel substrate
钢基体
1.
The present state of Al2O3 ceramic coating on steel substrate is summarized in this article,and some particular methods in the preparation are introduced,such as Hot Spray,Sol-Gel and thermo chemistry reaction,their excellence and disadvantage are also discussed and analyzed.
综述了目前钢基体上制备Al2O3陶瓷涂层的研究现状,详细介绍了热喷涂法、溶胶-凝胶法及热化学反应法3种制备Al2O3陶瓷涂层的主要方法,并探讨和分析了它们各自的优缺点。
2.
The bonding strength between cermet cladding and steel substrate was expressed using the bonding strength of two bonded steel plates bonded by cermet cladding material.
根据液相烧结三元硼化物基金属陶瓷覆层材料的工艺特点,用金属陶瓷覆层将两钢板进行液相烧结连结,以覆层对两钢板的连结强度表征覆层与钢基体的结合强度。
3.
Moreover, the technological requirement of making copper metl and keeping steel substrate unmelt could only be achieved under optimized parameters.
本文主要研究钢基体无熔深熔敷铜高频感应焊接温度场的数值模拟。
3) steel matrix
钢铁基体
1.
Non-cyanide alkaline copper plating process on steel matrix;
钢铁基体上碱性无氰镀铜
2.
The progress in the study of cyanide-free copper electroplating on steel matrix is introduced according to different valences of copper in the deposition process.
按照沉积过程中铜的价态的不同对在钢铁基体上无氰碱性镀铜的研究进展进行了说明。
4) matrix steel
基体钢
1.
The mechanical properties of matrix steel 7CrMo4SiV1 and its plasma nitrocarburizing and TiN deposition properties have been studied.
研究了基体钢 7Cr4MoSiV1的力学性能和其离子氮碳共渗和气相沉积TiN工艺。
2.
Effective factors such as the temperature and the time of pack carburizing,the austenizing temperature, the holding time and the tempering temperature on the hardness and toughness of matrix steel 65Nb are reported.
研究了固体渗碳温度、渗碳时间、淬火加热温度和保温时间、回火温度等对６５Ｎｂ基体钢硬度和韧性的影响。
3.
By means of a heating-cooling and microstructure analysis,an investigation is made on the phase regions at 1 500 ℃ to room temperature and the change of phase constituents at different cooling rates on the matrix steel type 65Cr4W3Mo2VNb(steel 65Nb for short).
通过加热一冷却一组织分析法，研究了含铌基体钢６５Ｃｒ４Ｗ３Ｍｏ２ＶＮｂ（简称６５Ｎｂ）从１５００℃至室温不同温度下，钥所处的相区及不同冷速条件下相组成的变化，初步探讨了６５Ｎｂ钢中的相关系。
5) 45 based steel
45钢基体
6) A3 steel substrate
A3钢基体
1.
The results show that the acceleration of NaCl,NH 4Cl,Na 2SO 4,Na 2SO 3 and FeSO 4 to corrosion of A3 steel substrate are all considerable,but that of NaCl is a little less than those of NH 4Cl,Na 2SO 4,Na 2SO 3;and that of FeSO 4 is slightly greater than those of the former.
对A3钢基体 ,NH4Cl、Na2 SO4和Na2 SO3 的腐蚀促进作用接近 ,FeSO4的影响略大于前几种可溶盐 ,而NaCl的影响略小 。
补充资料：基体钢
分子式：
分子量：
CAS号：
性质：一种特殊用途工具钢，其化学成分相当于高速钢的基体成分，在正常热处理后其组织与高速钢基体相同。这种钢具有接近高速钢的强度并且具有相当好的韧性，可用来制造高硬度耐冲击工具。
分子量：
CAS号：
性质：一种特殊用途工具钢，其化学成分相当于高速钢的基体成分，在正常热处理后其组织与高速钢基体相同。这种钢具有接近高速钢的强度并且具有相当好的韧性，可用来制造高硬度耐冲击工具。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条