1)  leak
泄露点
2)  leakage
泄露
1.
Study on Leakage Reasons of Pilot Valve in the Hydraulic Support;
液压支架中操纵阀泄露问题的研究
2.
LNG leakage may possibly happen at any times to LNG receiving terminal and those equipments at seaports, the dangers and damages of which should be paid much attention to.
为此,介绍了我国LNG进口和终端建设情况,结合国内外LNG泄漏与扩散的试验和模拟,对可能发生的LNG船舶碰撞危害性、LNG泄露的扩散和火灾危险性等方面研究进行了综述和分析,并对其中的不确定性问题进行了讨论,给出了进行LNG风险评价的建议。
3.
A coal-cutting machine often occurs leakage,the paper introduces sorts and general selecting rules of seal elements.
针对采煤机常出现的泄露现象 ,介绍了密封的种类和密封件选用的一般原则。
3)  leak
泄露
1.
Analysis of effect on environment of leak from tank car carrying liquid choline;
液氯罐车泄露事故对环境的影响分析
2.
A model of letting out of no oil ubricated double whirlpools vortex air compressor was set up,The length of leak line of one cycle was calculated the change of the leak line at work,The change of the length of leak line varying with the crank corner,and the change of the leak amount varying with the pressure of revealing atmospheric and crank corner were analyzed.
建立了无油润滑双涡圈涡旋压缩机的泄露模型,根据型线的几何理论计算了一个周期内泄漏线的长度,分析了在工作过程中泄漏线的变化,泄漏线长度随曲柄转角的变化,以及泄露量随排气压力,曲柄转角的变化情况。
4)  Revelation
泄露
1.
With the promotion and pauperization of the network technology application, the dependence on the network of the people is growing day by day; however, when enjoying the net surfing, the people are also bothered by the illegal tracking and revelation of personal computer systems.
随着网络技术的推广和应用的普及,人们对网络的依赖度在与日俱增,然而,当人们在体验着网上冲浪的无限快乐时,也在为上网行踪被跟踪、个人计算机内的信息被泄露而烦恼。
5)  seal leakage
密封泄露
1.
Causes and prevention of mechanical seal leakage of circulating pump in copper electrolysis system;
铜电解系统循环泵机械密封泄露的原因与防治
6)  Chlorine leakage
氯气泄露
参考词条
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。