1) composite copper coating
复合镀铜层
1.
Influence of electrodepositing parameters on composite copper coating with liquid hydrophobic agent microcapsules
电沉积参数对含憎水剂微胶囊复合镀铜层的影响研究
2.
Properties of the composite copper coating with liquid microcapsule were studied.
研究了含有有机硅树脂为囊心的液体微胶囊复合镀铜层的性能。
3.
An electrodepositing composite copper coating had been obtained by adding the liquid microcapsule containing orhanosilicon resin in acidic copper bath.
讨论了用水相分离法制备含有液体微胶囊的技术,并将以有机硅树脂为囊心的液体微胶囊加入到酸性镀铜液中进行复合共沉积,得到了含有液体微胶囊的复合镀铜层。
2) copper-based composite coating
铜基复合镀层
3) composite coating
复合镀层
1.
Study on technology of brush electroplating Ni-PTFE composite coating;
电刷镀Ni-PTFE复合镀层工艺研究
2.
Spectrophotometric determination of total precipitated quantities of nano-sized aluminium oxide in composite coatings with chrome azurol S;
铬天青S分光光度法测定复合镀层中纳米粉体氧化铝共析量
3.
Study on preparation and properties of nano Ni-SiC amorphous composite coatings;
纳米Ni-SiC非晶态复合镀层的制备工艺及性能研究
4) composite coatings
复合镀层
1.
Microtensile property of nano WC and PTFE composite coatings;
纳米WC和纳米PTFE的复合镀层微拉伸研究
2.
Study on properties of electrodeposited RE-Ni-W-B composite coatings;
电沉积RE-Ni-W-B多元复合镀层性能研究
3.
Study on preparation of Ni-P-SiC(C) composite coatings by electroless deposition;
化学沉积法制备Ni-P-SiC(C)复合镀层的研究
5) composite plating
复合镀层
1.
Study on microstructure and properties of electroless RE-Ni-Mo-P-WC composite plating;
化学沉积RE-Ni-Mo-P-WC复合镀层组织结构及性能研究
2.
The Effect of P Content in Ni-P-Si_3N_4 Composite plating on Remanent Stress and Wear Performance;
Ni－P－Si_3N_4复合镀层中P含量对残余应力和磨损性能的影响
3.
The performance and quality of taps before and after composite plating were compared separately.
介绍了国内机用丝锥和挤牙丝锥上化学镀覆(Ni-P)-SiC-PTFE复合镀层的应用情况。
6) composite layer
复合镀层
1.
Plus-deposited nanometer Ni-TiN composite layers;
脉冲电沉积纳米Ni-TiN复合镀层
2.
Study on Microstructure and Properties of Ultrasonic-electrodeposited Ni-TiN Composite Layer
超声-电沉积Ni-TiN复合镀层组织和性能研究
3.
Adhension and conductivity of the composite layer were studied.
采用化学复合镀技术在尼龙塑料PA66表面沉积PANI/Cu复合镀层。
补充资料：镀铜
镀铜
copper coating
dUtong镀铜(eopper eoating)在酸洗后的盘条(线坯)表面镀覆一层铜，以作为拉丝时的润滑载体。以铜层作润滑载体主要用在拉拔轮胎钢丝与气体保护焊丝等特殊场合，这时铜层除用作润滑载体外，可提高轮胎钢丝同橡胶的结合力和焊丝的导电性。此外也用于弹妥钢丝等的生产中，以改善拉拔时的润滑性能及产品的表面质量。 镀铜操作时，把盘条浸入加有一定硫酸和骨胶的硫酸铜溶液中。根据电位序，铁能置换铜: Fe+CuZ+-今Cu+FeZ+并很快发生下列反应和完成镀铜过程 Fe+CuSO;一FeSO‘+Cu专硫酸铜是溶液的主要镀剂，提供铜离子的来源，浓度通常控制在60一7馆/L。浓度过低，将延长镀铜时间且不易获得所需厚度的镀层;浓度过高，则铜的沉积速度过快，导致铜结晶迅速长大，使镀层疏松、粗糙，影响与基体的结合。硫酸的主要作用是活化盘条表面，使铜层能与基体牢固结合。骨胶有促使铜与基体粘合的作用，并使铜层结晶细密。镀铜时溶液温度必须控制在簇25℃，温度较低时，镀层光亮致密，但生产率低。温度过高时，则镀层厚，且粗糙、疏松、附着力差。溶液中Fe2+离子过多会恶化镀层质量。镀铜过程约在1一2而n内完成。 (韩观昌)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条