说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 细磨介质
1)  Fine grinding media
细磨介质
1.
Comminuting effect in grinding process by using cast iron segment as fine grinding media is studied with comparison to steel ball.
采用普通钢球作为对比,研究磨矿过程中以铸铁段为细磨介质的破碎效果。
2)  Grinding medium
磨矿介质
1.
The short cylindrical grinding medium is benefittal to the selective grinding of bauxite, but the increasing of the mass ratio of Al_2.
研究了球形、短圆柱形和短圆柱+球形3种磨矿介质对铝土矿选择性磨矿的作用。
2.
The effect of grinding medium on calamine and magnesite flotation using sodium oleate as collector was investigated.
采用钢球和氧化锆球两种球介质,研究了磨矿介质对菱锌矿和菱镁矿表面性质及油酸钠浮选体系中浮选回收率的影响。
3)  grinding media
磨矿介质
1.
Effect of grinding media on the flotation of carbonate using sodium oleate as collector
磨矿介质对油酸钠浮选碳酸盐的影响
2.
Optimization of grinding media of regrinding mill in beneficiation plant
选矿再磨机磨矿介质的优化研究
3.
The effects of grinding media on surface properties and flotation performance of galena are investigated by means of SEM,XPS and flotation experiment.
利用SEM、XPS及浮选试验考察磨矿介质对方铅矿表面性质和浮选行为的影响。
4)  grinding medium
研磨介质
1.
Also,the experiments had been carried out to study the effects of the high-pressured water jet power,the amount and composition of grinding medium and the impact time on the comminuting capability.
通过试验方法研究了高压水射流功率、研磨介质的填充量和配比、冲击时间等对该装置粉碎能力的影响。
5)  ball mediums
磨矿介质
1.
This paper studies that the ball mediums in the URSBM go through three steps: uniform circumference motion, motion on the surface of guidance arc plate and parabola motion, and researches on the kinematics regularity of the ball mediums.
针对超临速球磨机磨矿介质运动的三个阶段:圆周运动阶段、沿导向板滑落阶段、抛物线冲击矿石阶段,对超临速球磨机磨矿介质运动规律进行了研究,得出了超临速球磨机磨矿介质的运动轨迹方程、对矿石的冲击速度、冲击力公式和冲击次数等。
2.
Based on the industrialization design of URSBM,this paper studies shock characteristic of ball mediums in the URSBM.
在超临速球磨机工业化设计的基础上,对超临速球磨机的磨矿介质冲击特性进行了研究、分析,推导出超临速球磨机磨矿介质钢球的冲击速度和冲击力计算公式。
6)  Grinding Media
研磨介质
1.
By applying the commercial wet stirred mill,the effect of behavior of grinding media,such as the kinds of media,the ratio among grinding media in size and the ratio of media and feeding on ultrafine grinding of roasted kaoline is investigated.
在优化研磨介质等条件的基础上 ,进行了模拟生产状态的连续磨矿试验 ,实现了磨矿产品小于 2 μm的颗粒质量分数大于 90 %的预期结果。
2.
With a comparison test between the Φ 1 8 mm neutral glass beads and Φ 4 mm common glass beads in sand mill, a grinding efficiency curve was obtained, with which the abrasion loss of the grinding media was calculated It has shown that the Φ 1 8 mm neutral glass beads shows higher grinding efficiency, lower abrasion loss and cos
通过Φ18mm中性玻璃珠和Φ4mm普通玻璃珠研磨介质的对比试验,绘制了研磨效率曲线图,计算了研磨介质的磨损量。
3.
Through analyzing motion state of grind media in Ball Mill,the motion state of free fall grinding medium can be find out clearly,and its running parameter of grinding media can be distinctly calculated which in turn is very useful for controlling ore character.
通过对球磨机内研磨介质运动状态的分析,可以明确的了解抛落式运动状态的研磨介质的运动状态,从而清楚的计算出研磨介质的工作参数。
补充资料:染料砂磨介质
分子式:
CAS号:

性质:染料砂磨所用的物料。多选用渥太华砂、天然砂、玻璃珠和陶瓷球等。要求耐腐蚀强,在砂磨过程中不影响浆液的PH值,破碎率低,长期使用不因砂粉影响生产。砂磨介质与浆料的比例为(1~2):1(质量比),砂磨介质为中性,如0.8~1mm的中性耐磨蚀玻璃珠。不同染料、不同生产工艺、不同厂家,选用的砂磨介质直径也有不同。还有两种直径不同的玻璃珠混合起来使用的。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条