1) transverse stress
横向应力
1.
The research on the bridge slab transverse stress analysis of the ribbed plate concrete cable stayed bridge
肋板式混凝土斜拉桥桥面板横向应力分析研究
2.
A post-processing method was used to compute the transverse stresses in composite shells of revolution.
采用了一种应力后处理方法以准确计算复合材料旋转壳体中的横向应力。
2) lateral stress
横向应力
1.
The longitudinal and lateral manganin gauges were used to determine the principal stresses in the shocked specimens,the lateral stress and longitudinal stress were measured in the 3～11 GPa range of shock stresses.
通过一维平面撞击实验 ,在Al2 O3抗弹陶瓷材料中进行了冲击波速度、飞片速度的测量和纵向应力、横向应力测量 ,得到了Al2 O3抗弹陶瓷的冲击波D up 关系 ,以及抗弹陶瓷在 3～ 1 1GPa压力范围内相应的横向应力和纵向应力关系曲线 ,并根据这一曲线得到了抗弹陶瓷的纵向应力与剪切强度的关系。
2.
The experimental results indicate that the lateral stresses can be calculated directly from the piezoresistance expression calibrated by longitudinal stresses with the method of strain remedy by constantan gauge as the lateral stresses in anti-shoot ceramic are measured.
实验结果表明 ,在陶瓷等硬质材料中进行横向应力测量时 ,可用康铜计补偿的方法 ,直接用锰铜计纵向标定的压阻系数计算 ,而在有机玻璃中却不能简单地得到横向应力。
3) transverse stresses
横向应力
1.
Steady state vibration and transverse stresses of submarine pressure hull with anechoic tile;
带有消声瓦的潜艇耐压壳的稳态振动和横向应力
2.
Damped vibration and transverse stresses of visco-elastic laminated plates;
粘-弹层合板的阻尼振动和横向应力
3.
And the reasonable transverse stresses can be obtained.
基于分层理论并在壳厚方取二次位移插值函数来推导出粘弹层合壳的动力学方程,得出的简支粘弹层合壳自由振动频率和损耗因子与已知文献数据吻合较好,且能够计算协调的横向应力。
4) transverse shear stress
横向剪应力
1.
Based on the Reissner-Mindlin type global displacement field and predictor-corrector method, the transverse shear stresses are investigated for laminated composite plates subjected to thermal load.
基于Reissner-Mindlin型全局位移场模型和有限元预测-修正分析过程,数值计算和分析了复 合材料层合板受热载荷作用下的横向剪应力。
2.
Based on the Reissner Mindlin type global displacement field and predictor corrector method, the deflections and transverse shear stresses were investigated for laminated composite cylindrical shells under mechanical load.
本文根据ReissnerMindlin型的全局位移场(一阶和三阶),应用有限元预测—修正法,数值计算和分析了机械载荷作用下复合材料层合圆柱壳的挠度和横向剪应力。
3.
Secondly, by mean of 3-D stress equilibrium equations and Lagrange's interpolation, the least-square fit was adopted to determine the transverse shear stress.
首先按照一般的有限元分析过程(没有引入剪切修正系数)计算出全局响应(如挠度,频率和屈曲载荷等)的预测值;然后利用Lagrange插值构造横向剪应力的一般形式,使得满足层间连续和表面上为零的条件,通过最小二乘法拟合三维应力平衡方程获得横向剪应力;最后在单元上计算和引入剪切修正系数,再经过有限元分析计算出全局响应的修正值。
5) transverse tension stress
横向拉应力
6) transverse prestressing
横向预应力
1.
On construction technology of transverse prestressing in cast-in-place beam
现浇梁横向预应力施工技术
2.
this paper analyzed the wide concrete girder mechanical behavior under transverse prestressing by the spatial finite element method(FEM).
针对桥面宽混凝土梁,通过空间有限元分析,研究在张拉横向预应力钢束时混凝土梁的力学行为,得出有益于设计和施工的结论。
3.
To ensure the integrity of the girder and resist transverse bending due to dead load and service load,powerful transverse prestressing tendons were disposed in the diaphragms.
为加强主梁受力的整体性,抵抗静载和动载产生的横向弯矩,横梁结构内设置了横向预应力钢束。
补充资料：轧辊残余应力(见轧辊应力)
轧辊残余应力(见轧辊应力)
residual stresses in roll
zhagun eanyu yingli轧辊残余应力(residual stresses in roll)见礼辐应力。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条