|
1) key measures
工艺要点
1.
This paper introduces the status of development of polylaticmacid fibre and the main properties of polylaticmacid fibre,and discusses the key measures to produce polylaticmacid fabric to improve its spinnablity and control dyeing technology parameters during the processes of its spinning and finish.
分析了聚乳酸纤维产品的研究开发现状,介绍了聚乳酸纤维的生产及性能,结合纤维性能的特点,总结出开发服用聚乳酸纤维产品的工艺要点在于:纺纱中要提高纱线的抱合性,染整中应选择合适的染料及严格控制温度。
2.
This paper introduced the status of development of natural color cotton fabrics and the main properties of natural color cotton fibre,and discusses the key measures to produce it.
分析了彩棉纺织品的研究开发现状 ,介绍了天然彩棉纤维的性能及开发彩棉产品的工艺要点。
2) Main points of rolling process
轧制工艺要点
3) Major Process
主要工艺
1.
Major Process and Development Tendency for Urban Wastewater Treatment of Our Country;
我国城市污水处理的主要工艺及发展趋势
4) technological requirement
工艺要求
1.
Construction Procedures and Technological Requirements for Segments of Main Girders of Cable-stayed spans of the Second Changjiang River Bridge in Wuhan;
武汉长江二桥斜拉桥主梁节段施工步骤和工艺要求
2.
This paper discusses on the technological requirements, features, kinds and mechanism of the treatment of oily waste water, and introduces some kinds of oily waste water treating techniques, including physical treatment, chemical treatment, physicochemical treatment and biochemical treatment.
论述了含油污水处理的工艺要求、特征、种类及其机理,介绍了几种含油污水处理技术,包括物理处理技术、化学处理技术、物理化学处理技术和生化处理技术。
3.
The value,characteristic,quality level,and technological requirement of mat art glaze were discussed in order to correctly know and develop him,and set up the level of mat art glaze in China.
主要论述了无光美术釉的价值及其特征、质量标准、工艺要求,以便对其具有正确认识,促其发展,建立中国的标准。
5) process requirement
工艺要求
1.
According to process requirements,large-span steel beam is overhead welded with steel pillar.
大跨度钢架横梁在高空与钢柱对接焊,利用“马鞍”进行刚性固定,边柱垂直度向外偏移,按工艺要求组织施工,为今后类似工程提供参考。
2.
The production technology of modified ANFO is discussed, and the process requirements of three key quality check points—formulation design, modified process control and follow-up charge process control, is analyzed combining with the situation of practical production.
对改性铵油炸药的生产工艺进行了探讨,结合生产实际情况分析了配方设计、改性工艺控制及后续装药过程控制三个关键质控点的工艺要求,解决了生产中出现的问题。
6) technological requirements
工艺要求
1.
The coating technological requirements and technological process are briefly introduced.
介绍了涂装工艺要求和工艺流程,重点介绍了混凝土搅拌车的涂装工艺、涂装设备和混气喷涂工具,对提高混凝土搅拌车等重型专用汽车的涂装质量有一定的指导意义。
补充资料:常用塑料主要性能及注射成型工艺要点
GPPS及其改性物----HIPS.AS(SAN).BDS(K-Resin) 价格最便宜 1. GPPS --- 硬胶.通用聚苯乙烯◎ 塑料主要性能:a) 高透明度, 良好光泽, 容易着色, 属非结晶塑料;b) 尺寸稳定性好(收缩率0.4%左右), 耐磨性差, 故胶件包装要求较高以防擦花;c) 制品对内应力敏感, 性脆, 无延展性, 冲击强度小,易开裂且断裂后易形成尖角(SHARP POINT)`利边(SHARP EDGE), 故单纯的GPSS料较少见用于玩具制造.◎ 注塑工艺要点: a) 原料一般不需干燥, 个别情况80℃烘2小时;b) 成型温度范围较大, 加热溶化及固化速度快, 故成型周期一般较短; 温度参数: 料筒温度200℃左右, 料温过高易出现银丝, 而料温过低会使透明性差;c) 模温控制: 模温一般在50-80℃;d) GPPS流动性很好, 啤塑中不需要高压力(通常注射压力10Mpa左右), 以免过大而增加胶件内应力----可能导致开裂(尤其是经油漆装饰工序后);e) 注射速度直适当高以减弱夹水纹, 但因注射速度受注射压力影响大, 过高的速度可能会导致披锋或出模时粘模以及顶出时顶白顶裂等问题;f) 适当的背压: 如果背压太低, 螺杆转动易溢入空气, 料筒内料粒密度小, 胶粒塑化效果不好, 影响胶件表观质量(一般背压取10-20kg/cm2);g) 模具上一般设计细水口为0.8-1.0mm.h) 玻璃纤维强化型PS-GF30,料筒温度为180~275,模具温度为20~80,成型收缩率0.1~0.2.密度1.29/cm3◎ 共混改性塑料: GPPS + PVC→共混成为性能较好的不燃塑料;◎ 常用原料举例:a) 奇美硬胶PG-33 (台湾奇美实业公司); b) STYRON 666D (美国道化学公司);c) Bakelite SMD-3500 (美国联合碳化物有限公司). 2.HIPS --- 不碎胶. 高冲击聚本乙烯 @ 塑料主要性能:a) 着色性好;b) 与GPPS比较是加入了5-20%的丁二(一般用顺丁橡胶或丁苯橡胶), 成份, 故抗冲击性大大提高.@ 注塑工艺要点:a) 流动性小于GPPS, 故成型温度` 压力都稍高;b) 冷却速度较GPPS慢, 故需要足够的保压力和保压时间以及充分的冷却条件以减少局部收缩及冷却变形. @ 共混改性塑料: HIPS + GPPS→混和啤塑, 调整比例使塑料具有足够强度及良好表观质量. @ 常用原料举例:a) HIPS STYRON 470,475U (DOW Chemical Co., Ltd)b) Dolyrex PH-66 (台湾奇美实业公司)c) HIPS HI-425 (NIWON Co., Ltd 。KOREA)3. AS(SAN) – 大力胶. 丙烯晴-苯乙烯共聚物 @ 塑料主要性能:a) 高透明` 高光泽` 耐冲击性优于GPPS;b) 不耐动态疲劳, 但耐应力开裂远胜GPPS. @ 主要工艺要点:a) 需进行预干燥, 80℃2小时;b) 温度控制: 注射成型温度180-270℃, 模具温度65-75℃.c) 玻璃纤维强化SAN-GF30, 需进行预干燥, 80℃2小时, 温度控制: 注射成型温度200-260℃, 模具温度60-80℃,成型收缩率0.1~0.2% @ 常用原料举例: AS767 / STYLON GR601 (旭 DOW。日本)4. BDS(K-ResinK树脂) –料。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条
|