说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 半轴齿轮
1)  half axle gear
半轴齿轮
1.
A discussion is made on the problems of original dies for precision forging of half axle gear of automobile differential,the forging technique and the design of forge piece are improved,and the new type of blocker die and finish forging die is designed.
论述了精锻汽车差速器半轴齿轮原模具结构存在的问题,改进了锻造工艺和锻件设计,设计了新型粗锻模和精压模。
2)  semi-axle bevel gear
半轴锥齿轮
1.
A new precision forming technology was presented,which uses an ordinary forging machine and a high precision rotary forging machine to make the closed-tolerance semi-axle bevel gear forgings.
提出了采用普通锻压设备进行坯料准备、高精度冷摆辗机成形半轴锥齿轮精锻件的成形新工艺,研究了成形工步的坯料形状、成形工艺参数、模具结构以及精锻件后续加工的工装夹具结构等一系列技术问题。
3)  axle shaft gear
驱动轴齿轮;半轴齿轮
4)  Axle shaft gear die
半轴齿轮模具
1.
In view of the characteristics of the Axle shaft gear die that there existing a lot of standard parts and typical structures in the die,a 3D standard-part database for the Axle shaft gear die was built on the platform of SolidWorks by using the VB object-oriented programming technology.
介绍了以SolidW orks为开发平台,以VB为面向对象的编程技术,针对半轴齿轮模具中存在大量的类标准零部件这一特点,建立了三维半轴齿轮模具的标准零件库。
5)  semi_shaft spur conical gear
半轴直齿圆锥齿轮
1.
It was turned out that control on the die flash height is a simple and effective way for extending the service life of the fine forging die for semi_shaft spur conical gears.
论述了模具飞边高度的调整对锻造冲击力、模膛内部压力、齿形模大端变形和锻件实际飞边厚度增加产生的影响 ,得出控制模具飞边高度是简单、有效地提高半轴直齿圆锥齿轮精锻模具使用寿命的方法 ,在生产中得到较好的应
6)  rear axle differential side gear
后桥差速器半轴齿轮
补充资料:卧式单轴、多轴自动半自动操作规程
适用机型:
1、 单轴自动车床:
CG110(1A10?),C1318(1A118),C1325(1A124),
C1336(1A136),A12,A20,A40。
2、 多轴自动、半自动车床:
C24·4(1240·4),C25·4,C2140·P4,C2150·4D,C2132·6D,C2132·6,
C24·6(1240·6),C2150·6D,C2216·6,BSA1/2 -4,1290,ANK135,
ANK155,1261M,1261?,1265·6,1265M·6,1240-0
一、认真执行《金属切削机床通用操作规程》有关规定。
二、认真执行下述有关补充规定:
(一) 工作前认真做到:
1、 检查分配轴及凸轮上的凸轮、撞块应完好无裂纹,安装正确,紧固牢靠。
2、 调正机床时,棒料、毛坯的夹紧,只准用手动不准用机动。
(二) 工作中认真做到:
1、 不准加工弯曲、未经冷拨和未经倒角的棒料。
2、 装料时须将料头对准夹头孔,轻轻击进。棒料长度一般以不超出料管200毫米左右为宜。
3、 四轴自动车床不准在第四工位上装料。六轴自动、半自动车床不准在第六工位上装料。
4、 保险键剪断时,就应查明原因,方准更换新键。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条