1) piezoelectric laminated plates
压电层合板
1.
Bending of composite materials cantilever piezoelectric laminated plates based on nonlinearity;
基于非线性的压电层合板弯曲
2.
Using the robust control method to control the vibration of piezoelectric laminated plates;
压电层合板振动的鲁棒控制
3.
The solution of the thermal buckling problems of piezoelectric laminated plates is presented in the context of the mathematical theory of elasticity.
本文在作者们以前工作的基础上导出了热压电介质弹性稳定性问题的控制微分方程，提出了热压电层合板热屈曲问题的数学弹性力学解法。
2) piezoelectric laminated plate
压电层合板
1.
This paper analyzes the deformations in unbalanced piezoelectric composites under the same loads and driving voltages using the 4-node rectangular piezoelectric laminated plate finite element, which is based on the first-order shearing deformation theory.
利用基于一阶剪切层合板理论的四节点矩形压电层合板板有限单元,分析了在外载荷和驱动电压相同的情况下,五种不同铺层形式的压电复合材料变形的规律;同时对压电非均衡复合材料中弯-扭耦合系数对其变形规律的影响进行了初步的研究。
2.
Considering the effects of piezoelectricity and geometrical nonlinearity,the non-linear dynamic equations of piezoelectric laminated plates are established.
基于损伤力学,考虑压电效应、几何非线性和损伤演化的影响,建立了集中载荷作用下压电层合板的非线性运动微分方程,考虑撞击物与压电层合板之间的弹性接触效应,确定了层合板所承受的冲击力。
4) piezoelectric laminates
压电层合板
1.
Analysis of transient responses in piezoelectric laminates excited by coupled electro-mechanical loads;
机电耦合载荷下的压电层合板瞬态响应分析
5) piezoelectric laminate
层合压电板
6) piezoelectric laminated circular plates
压电层合圆板
1.
Von Karman equation of axisymmetric piezoelectric laminated circular plates is obtained with a view to influence of the electrostrictive nonlinear piezoelectric effects and geometric nonlinearity.
本文研究可移简支及夹支边界条件下,轴对称压电层合圆板在强电场和机械荷载联合作用下的非线性变形,考虑电致伸缩的非线性压电效应及几何非线性,导出轴对称压电层合圆板的von Karman方程,利用幂级数法求解,得到强电场和均布载荷作用下的挠度、轴力及轴向位移的解析表达式,通过对双压电晶片执行器的数值计算及分析,得到线性与非线性模型之间的差别和适用范围。
2.
The governing equations of axisymmetric piezoelectric laminated circular plates are obtained as viewed from the nonlinear electrostrictive piezoelectric effects and geometric nonlinearity.
研究可移简支及夹支边界条件下,轴对称压电层合圆板在强电场和机械荷载联合作用下的非线性变形。
补充资料：N,N-二缩水甘油2,4,6-三溴苯胺玻璃布层合板
分子式：
CAS号：
性质：以三溴苯胺环氧树脂为基料的玻璃布层合板。耐燃性好，相对密度>1.98。机械强度除冲击强度(190kJ/m2)和剪切强度(119MPa)外，其他略次于E-51环氧树脂。将三溴苯胺环氧树脂与有关添加剂配成胶液后，手工糊于玻璃布上，叠层并层合固化即得。可用于要求耐燃的航空、船舶和机电行业。
CAS号：
性质：以三溴苯胺环氧树脂为基料的玻璃布层合板。耐燃性好，相对密度>1.98。机械强度除冲击强度(190kJ/m2)和剪切强度(119MPa)外，其他略次于E-51环氧树脂。将三溴苯胺环氧树脂与有关添加剂配成胶液后，手工糊于玻璃布上，叠层并层合固化即得。可用于要求耐燃的航空、船舶和机电行业。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条