说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 局部热冲锻
1)  sheet press forging
局部热冲锻
1.
Sheet warm forming process, sheet warm hydroforming process and sheet press forging process are introduced in this paper.
介绍了镁合金薄壁板材的温热冲压成形技术、温热液压成形技术和局部热冲锻成形技术。
2.
Warm forming process,warm hydro-forming process and sheet press forging process are introduced in this paper.
本文介绍了镁合金薄壁板材的温热冲压成形技术、温热液压成形技术和局部热冲锻成形技术。
2)  local scour
局部冲刷
1.
Experimental study of local scour for No.2 floating cofferdam of Wuhan Tianxingzhou Rail-Cum-Road Bridge;
武汉天兴洲公铁两用桥2~#浮运围堰施工期局部冲刷试验研究
2.
Study on local scour around a large circular cylinder under irregular wave action;
不规则波作用下墩柱周围局部冲刷研究
3.
Research on local scour during settling of steel caissons for large-scaled bridges;
大型桥梁钢沉井下沉过程局部冲刷研究
3)  local scouring
局部冲刷
1.
Properties of protection engineering against local scouring around piers;
桥墩局部冲刷防护工程特性研究综述
2.
In this paper,by setting up a 1∶100 large scale normal physical model of local stream segment,the sizes of the local scouring pits around the Bridge piers have been researched,particularly the scouring range of the south auxiliary piers and influences of the pier local scouring on the south bank slope stab.
通过建立1∶100大比例尺正态局部河段物理模型,研究了桥墩局部冲刷坑大小尺寸,特别是南辅助墩冲刷范围,以及桥墩局部冲刷对南岸岸坡稳定产生的影响。
3.
In the light of the local scouring that will be caused by floating construction of the cofferdam for Pier No.
针对天兴洲大桥2号墩浮运围堰施工冲刷,采用现行规范中的桥渡冲刷计算原理进行计算分析,初步认识冲刷计算式的结构特性;进行局部冲刷水槽试验,进一步深入研究分析行近水深、行近流速以及围堰入水深度对浮运围堰冲刷的影响;利用冲刷计算与试验结果,为2号墩浮运围堰施工期安排提供有力依据。
4)  local scour depth
局部冲深
1.
Theoretical discussion on calculation of local scour depth of spur dikes;
丁坝局部冲深计算的理论探讨
5)  local erosion-deposition
局部冲淤
6)  component impulse
局部冲动
补充资料:热冲
分子式:
CAS号:

性质:将热固性塑料层压板或热塑性塑料片材加热至适当温度下进行冲切加工的方法。相对于常温下的冷冲而言。常用于为避免常温下冲切易脆的片材时发生龟裂、脆裂、产生毛边的情况,以及冲切厚层板材时减少冲切力的场合。酚醛树脂层压板通常就采用热冲压。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条