1) high carbon medium-alloy steel
高碳中合金钢
1.
Transformation and morphology of carbides in high carbon medium-alloy steels during transforming process;
三种高碳中合金钢在热处理过程中的碳化物转变及形貌
2.
The investigation shows that M23C6 and M3C in Cr-W-Mo-V high carbon medium-alloy steels gradually dissolve into the matrix during heat process at about αγ temperature, and gradually precipitate again from the matrix during low cooling process.
研究表明,Cr-W-Mo-V高碳中合金钢加热至αγ温度区附近,M23C6和M3C会逐渐溶解于基体中,缓冷过程逐渐析出M23C6、M3C,并在αγ温度区发生M23C6M6C转变,而球状VC则变化不大,其碳化物超细化主要南溶解、形核的转变过程所引起的。
2) high-carbon medium-chromium alloy steel
高碳中铬合金钢
1.
The high-carbon medium-chromium alloy steel was austemper heat treated, and the optimum chemical composition was determined using orthogonal design.
1%C、3%~5%Cr的高碳中铬合金钢进行了等温淬火热处理,采用正交设计确定最佳化学成分配比,得到理想配合的材料韧性和硬度,将所得高碳钢与低碳钢复合铸造双金属复合衬板。
3) MCHAHS
中碳高合金高强度钢
1.
In this paper,through analysis of austenite-ferrite transformation in MCHAHS, taking the change of lattice parameters in phases into account,a ne.
以中碳高合金高强度钢(MCHAHS)的奥氏体-铁素体相变过程为主要研究对象,通过确定冷却过程中各生成相的晶格常数随温度的变化关系,发展了一种新的由线膨胀量信息提取相变动力学信息的计算方法。
4) High Carbon Alloy Steel
高碳合金钢
1.
Application of Phase Equilibrium Thermodynamic Method in Alloy Design for High Carbon Alloy Steel with Ultra Fine Carbides;
相平衡热力学方法在超细碳化物高碳合金钢合金设计中的应用
2.
Calculation of Equilibrium Phase for High Carbon Alloy Steel with Multiple Types of Ultra-fine Carbides and Examination in Heat Treatment Process;
多类型超细碳化物高碳合金钢的平衡相计算及热处理研究
3.
Up to now, the welding theory for high carbon alloy steel has not been well established.
迄今为止,高碳合金钢材料的焊接理论仍未完善。
5) carbon high-alloy steel
高合金碳钢
6) Medium carbon alloy steel
中碳合金钢
1.
The ability of spinning of medium carbon alloy steel at annealing is very good.
中碳合金钢退火状态可旋性良好,累计变薄率为80%,未见裂纹出现。
2.
Wear characteristics and mechanisms of a medium carbon alloy steel after quenching at 900 ℃ and low temperature tempering at 200 ℃ were investigated under the condition of impact corrosive wear.
为探讨较高的冲击力对中碳合金钢的冲击腐蚀磨损规律,对中碳合金钢经900℃淬火、200℃低温回火得到的复相组织的磨损特性和机理进行了试验研究。
补充资料：中合金钢
分子式：
分子量：
CAS号：
性质：合金元素的总含量一般是5%~10%的合金钢。
分子量：
CAS号：
性质：合金元素的总含量一般是5%~10%的合金钢。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条