1) cladding
[英]['klædɪŋ] [美]['klædɪŋ]
熔覆
1.
Study on microstructure and performance of Fe-base alloy coating produced by plasma cladding;
等离子束熔覆铁基合金涂层的组织与性能研究
2.
The research of laser cladding Co-base alloy coating on ductile cast iron;
球墨铸铁表面激光熔覆钴基合金涂层的研究
3.
Cladding of high speed steel by high power diode laser;
大功率半导体激光熔覆高速钢研究
2) laser cladding
激光熔覆
1.
In-situ synthesis of Co_p/Cu composite coating by laser cladding;
激光熔覆原位合成Co_p/Cu复合涂层
2.
Research progress of laser cladding on the surface of magnesium alloys;
镁合金表面激光熔覆研究现状
3.
Influence of rare earths on Fe-based amorphous composite coatings by laser cladding;
稀土RE对激光熔覆Fe基非晶复合涂层的影响
3) hybrid cladding
复合熔覆
1.
Analysis model and experimental research of dilution in laser induction hybrid cladding;
激光感应复合熔覆的稀释率分析模型及实验研究
2.
The morphology and action of interface in laser and induction hybrid cladding
激光感应复合熔覆的界面形态及其作用
3.
Based on powder feeding laser induction hybrid cladding experiments,the effect of processing parameters on the interface between the coating and the substrate is studied.
在送粉激光感应复合熔覆试验的基础上,研究了工艺参数对熔覆层与基体结合界面形态及组织结构的影响规律。
4) cladding
[英]['klædɪŋ] [美]['klædɪŋ]
熔覆层
1.
RE-WC-steel composite coatings were prepared on 45 steel substrate by using WC particle and 1Cr18Mn8Ni5N stainless steel by means of modified arc spray technique,then the coatings were fused by argon shielded arc cladding.
获得了由弥散分布的强化相增强的熔覆层,强化相主要是WC/W_2C;熔覆层与基体之间为冶金结合;熔覆层硬度可达750HV0。
2.
A hard and wear resistant Ni35B\|SiC coating is formed on a Q235 steel substrate by argon shielded arc cladding.
采用氩弧熔覆工艺在Q235基材上熔覆Ni35BSiC,获得硬度和耐磨性高的熔覆层。
3.
The results show that there is an obvious bright intermediate belt between cladding alloy layer and the body, good metallurgic bonding is formed.
对熔覆层显微组织形貌、硬度分布进行了分析研究。
5) cladding layer
熔覆层
1.
The cracks in the laser cladding layer are the main obstacle of the laser cladding technology application.
熔覆层中的裂纹是激光熔覆技术应用的主要障碍。
2.
The features and microstructure of the cladding layer and interface layer between cladding layer and copper substrate were analyzed.
对熔覆层和熔覆层与基体结合区的形貌和微观组织进行了研究。
3.
Based on the artificial neural network(ANN),a model is established to describe the laser cladding parameters and the characteristic and performance of laser cladding layers.
基于人工神经网络(ANN)技术,采用MATLAB作为开发平台,建立了激光熔覆参数与熔覆层特征及性能之间的关系模型。
6) reactive cladding
反应熔覆
1.
Using reactive cladding process to prepare metallic carbide coatings is in-site synthesizing cermet phase grains during the reaction to improve the wear-resistance and erosion-resistance properties of the matrix surfaces.
反应熔覆制备金属碳化物涂层是在熔覆过程中原位生成碳化物颗粒相,来增强基体表面的耐磨耐蚀性能。
补充资料：熔盐电解法生产铌粉(见熔盐电解法生产钽粉)
熔盐电解法生产铌粉(见熔盐电解法生产钽粉)
production of niobium powder by molten salt electrolysis
rongyand+onjlefa ShengChan n.fen熔盐电解法生产妮粉(produetion。fn;obi-um powder by molten salt eleetrolysls)见熔盐电解法生产担粉。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条