1) concave round angle radius
凹圆角半径
2) the radius of the round corner of concave-convex die
凸凹模圆角半径
1.
In this article,an experimental research on the thermal deep-drawing process of (AZ31) magnesium alloy sheets is carried out,and the effects of the radius of the round corner of concave-convex die and the conditions of friction and lubrication on thermal deep-drawing process of(AZ31) magnesium alloy sheets are analysed.
对AZ31镁合金板热拉深进行了实验研究,分析了凸凹模圆角半径大小、摩擦与润滑条件对AZ31镁合金板热拉深成形的影响。
3) Circular Bead Radius of Cavity Die
凹模圆角半径
1.
Influence on the Drawing Process with Varied Viscosity of Lubricant and Circular Bead Radius of Cavity Die;
润滑剂的粘度与凹模圆角半径对拉深工艺的影响
4) drawing edge radius
拉延凹模圆角半径
5) fillet radius
圆角半径
1.
The optimization of drawing technique was researched,and the influence of different blank holder force and minimum die fillet radius on stamping forming was studied as well.
对该零件成形工艺进行了优化,研究了不同的压边力、最小模具圆角半径对冲压成形的影响,通过对模拟结果的分析得出了空调前板的最优化成形方案。
2.
It is shown that,the smaller the fillet radius of the tip is,the better the effect of drag reduction is.
指出:沟槽尖峰处的圆角半径越小其减阻效果越好,沟槽斜面中下部的壁面应力随着圆角半径的减小而降低,但尖峰处的局部壁面应力会随之增大;来流速度对沟槽减阻率的影响很大,对于一种尺度的V型沟槽,存在着一个具有较好减阻效果的来流速度范围,而沟槽面在沿来流方向上的布置位置对减阻效果的影响非常小;沟槽尺度对减阻效果很剧烈;沟槽尖峰处生成的二次涡是产生减阻效果的根本原因,二次涡的强弱与沟槽减阻率的大小紧密相关。
3.
Analyzed the effect of drawing die fillet radius to drawing process, based on theory analysis and production practice, put forward a better simple calculation formula fillet radius, and carried on examples of calculation.
分析了连续拉伸模圆角半径变化对拉伸工艺影响,在理论分析和生产实践基础上提出了一种较好的简便计算凸、凹模圆角半径公式,并进行实例应用计算。
6) radius
[英]['reɪdiəs] [美]['redɪəs]
圆角半径
1.
And on the basis of analyzing the geometry characteristics of the side rail, the corners whose radius deteriorates the formability are modified.
重点对高强度钢纵梁内板的成形性进行了分析,并且在详细分析零件几何特点的基础上,对此模型的圆角半径进行了修改,修改后零件的成形性得到了显著提高。
2.
Effects of Spoke Transition Radius on the Service Stress Concentration of Mg Wheel;
对具有不同过渡圆角半径的轮毂在相同状况下进行有限元服役应力比较分析。
补充资料：上圆
1.指天。旧说以为天在上而圆，故称。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条