1) microyield strength
微屈服强度
1.
The influence of electric filed intensity during the process of aging in electric field on the microyield strength and micro\|plastic deformation behavior of 2024 aluminum alloy was studied.
研究了电场时效处理中电场强度对 2 0 2 4铝合金的微屈服强度和微变形行为的影响。
2.
The measuring method of the microyield strength has studied with the INSTRON testing equipment.
利用INSTRON试验机研究了微屈服强度的测试方法。
2) Micro-yield Strength
微屈服强度
1.
Through comparison between the micro-yield strength value of and the corresponding yield strength value of more than 130 samples, it is shown that the tedious micro-yield tests can be replaced by common and simple yield tests.
通过130多个铍试样的微屈服强度与屈服强度的比较试验证明,用常规简单的屈服强度试验代替冗长的微屈服强度试验是可能的。
2.
We research the micro-yield strength of 1Cr18Ni9Ti steel under the high temperature aging treatment,provide mechanical parameters for mechanical engineering.
测试1Cr18Ni9Ti合金钢高温时效处理状态下的微屈服强度,为工程实际提供力学参数。
3.
Dimensional stability of sub-micron Al2O3 /2024Al composites was studied by means of micro-yield strength measurement and TEM analysis.
本文利用微屈服强度测试和透射电镜分析,研究了亚微米级Al_2O_3颗粒增强2024Al复合材料的尺寸稳定性。
3) yield strength
屈服强度
1.
Effect of phosphorus on the yield strength of as-quenched GH761 alloy;
磷对GH761合金固溶水淬组织屈服强度的影响
2.
Study of influence factors of yield strength of oil and gas pipeline;
油气管道屈服强度影响因素的研究
3.
A modeling study of the yield strength of HRB335 hot rolled ribbed bar;
HRB335热轧带肋钢筋屈服强度模型研究
4) yield stress
屈服强度
1.
Based on the plain carbon steel with the chemical composition of 200MPa class steel the products of the yield stress of 400～500 MPa class and high-quality mechanical properties can be produced using the technology of chemistry tightly-tuning and controlled rolling - controlled cooling.
以屈服强度为 2 0 0MPa级的普碳钢为基本成分 ,采用成分微调与控轧控冷工艺相结合的技术路线 ,可将屈服强度提高到 4 0 0～ 5 0 0MPa,同时保证良好的综合性能。
2.
From the tests, a two-stage linear relation has been found between yield stress(σ_s) and strain rate(ε),σ_s=σ_0+klgε.
对４种金属材料进行了应变率为１０~（－４）—１０~３ｓ~（－１）的拉伸试验，结果表明，屈服强度随应变率的升高分两阶段线性升高。
5) yielding strength
屈服强度
1.
Yielding behavior of mismatched welded joint and prediction of its yielding strength;
非等强焊接接头屈服行为及屈服强度预测
2.
Mechanical properties of normalized and tempered 12Cr2Mo steel forgings,primarily yielding strength,were on the low side.
汽轮机用12Cr2Mo钢锻件经正火、回火后,其力学性能(主要是屈服强度)偏低,一次热处理后的合格率仅为50%,既造成该钢锻件大量热处理返修,又严重影响了生产周期。
6) yield point
屈服点,屈服强度
补充资料：补偿屈服强度
分子式：
CAS号：
性质：应变超过应力-应变曲线成正比例的初始部分的指定量时的应力值。此指定的应变量称残余应变，也称偏置值。报告补偿屈服强度时一定要同时指明此偏置值。此值一般用于该材料没有明显的屈服点的场合。可以认为是一人为规定的屈服点，用于作条件性的相对比较。
CAS号：
性质：应变超过应力-应变曲线成正比例的初始部分的指定量时的应力值。此指定的应变量称残余应变，也称偏置值。报告补偿屈服强度时一定要同时指明此偏置值。此值一般用于该材料没有明显的屈服点的场合。可以认为是一人为规定的屈服点，用于作条件性的相对比较。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条