1) Shu4 area
曙四区
1.
3D geological modeling of Dujiatai reservior in Shu4 area;
曙四区杜家台油层储层三维地质建模
2) Shusi-joint-station
曙四联
1.
This test was implemented in the forth Shusi-joint-station,and the optimum operation parameters and reasonable addition dosage were also determined.
针对曙光油田稠油污水的特点,在原有工艺流程的基础上,根据实际处理能力,选择合适的设备,对不同的污染物采取优先强化处理和逐段处理方式,在曙四联进行了现场试验,确定了最佳运行参数及合理的加药量。
3) Shu1 Area
曙一区
1.
Shu1 area of Shuguang oilfield has abundant ultra heavy oil reserves and is an important production superseding block of Liaohe oilfield.
曙光油田曙一区超稠油储量丰富,是辽河油田重要的产能接替区块。
2.
Oil wells in block Du84 of Shu1 area, Liaohe oilfield, are comprehensively evaluated by using single well economic evaluation system and are classified into class I, II and III.
应用单井效益评价系统 ,对辽河油田曙一区杜 84块油井进行综合评价 ,并划分出一、二、三类效益井 ;分析了成本构成 ,并对措施进行了优选 ,为该区下一步的油田开发奠定了基
4) Shu 3 area
曙三区
1.
Composite sand control pilot test in Shu 3 area;
曙三区综合防砂先导试验研究
2.
Shu 3 area is a light oil block with serious sand production problem, resulting in incomplete flood pattern and affecting development result.
曙三区是曙光稀油主力区块之一,由于出砂严重,造成实际注采井网不完善,影响开发效果。
3.
The integrated sand control approach of Shu 3 Area and Shen 67 Block in Liaohe Oil Region is the combina- tion of control and discharge,which lays stress on optimizing systematic construction of the new wells in Du 21 Block Shu 3 Area to supply efficient references for sand control of new wells.
辽河油区稀油油藏曙三区和沈67块的总体防砂思路是防排相结合,重点是在曙三区杜21块新井实施系统工程优化,为新井防砂提供有效的技术支持,并在老区老井防砂手段上进行技术改进与完善,解决了树脂砂强度的问题,完善了携砂液的性能,同时采用排砂、防砂相结合的方法,在两个区块共施工97井次,取得了良好的试验效果。
5) Shul area
曙一区
1.
Analysis of vertical producing degree in super heavy oil reservoirs of Shul area recovered by cyclic steam stimulation;
曙一区超稠油蒸汽吞吐油层纵向动用程度分析
6) Shu 1 area
曙一区
1.
Comprehensive evaluation for super heavy oil reservoir in Shu 1 area;
曙一区超稠油油藏综合评价研究
2.
Sewage treatment process has been upgraded to improve the quality of output water in Shu 1 area for its super heavy oil sewage.
针对曙一区超稠油污水特征 ,对污水处理工艺流程进行改造 ,以提高外输水水质。
3.
Method From steam soaking characteristics of super heavy oil in Shu 1 area, fluid producing profiles during flowing is tested with high temperature profile tester.
方法 依据曙一区超稠油蒸汽吞吐特征 ,选用高温产液剖面测试仪 ,对放喷期产液剖面进行测试。
补充资料：彻曙
1.犹彻旦。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条