说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 广义Usher模型
1)  generalized Usher model
广义Usher模型
1.
Based on water cut rising rules of water flooded oil fields,this paper predicts water cut using generalized Usher model.
基于水驱油田的含水上升规律,应用广义Usher模型进行含水率预测。
2.
In this paper, a new growth curve model has been established, namely the generalized Usher model, which is more flexible and adaptable.
Gompetz、Pearl、Usher和Weibull等4种生长曲线模型是应用较多的软土路基沉降预测模型,文章建立了一种具有更大灵活性和更广泛适应性的新的生长曲线模型———广义Usher模型,通过数学规划方法求解,从而可根据有限的实测沉降观测数据预测软土路基沉降发展过程。
2)  Usher model
Usher模型
1.
Prediction of the variation of single-well water-cut using Usher model;
应用Usher模型预测单井含水率变化
2.
Prediction of roadbed settlement by Usher model;
路基沉降预测的Usher模型应用研究
3.
Based on the study of growth curvature in life system,it introduces a general Usher model and affords a new model suiting for depletion drive.
基于对生命体系生长曲线的研究,引入广义Usher模型,给出了一种适用于封闭油藏溶解气驱阶段关于油藏动态指标预测的新模型。
3)  generalized model
广义模型
1.
The design and implementation of generalized model server;
广义模型服务器的设计与实现
2.
The method of generalized modeling in a large scale system was used for reference to construct a generalized model of SoftMan emotional control.
借鉴大系统控制论中广义模型化方法,建立了软件人情感控制的广义模型。
4)  generalized CAD modeling
广义CAD模型
1.
Disassemble sequence and route planning of automobile product based on generalized CAD modeling;
基于广义CAD模型的汽车产品拆卸规划
5)  generalized force model
广义力模型
1.
Based on the characters of car s following states,a new generalized force model is proposed.
为了更有效地模拟城市交通流,尤其是城市交叉口交通流的运行状况,在研究跟驰状态中车辆行驶特性的基础上,考虑车辆行驶的最大限制速度,提出了一种基于最大车速的广义力模型。
6)  generalized Bingham model
广义Bingham模型
补充资料:AutoCad 教你绘制三爪卡盘模型,借用四视图来建模型
小弟写教程纯粹表达的是建模思路,供初学者参考.任何物体的建摸都需要思路,只有思路多,模型也就水到渠成.ok废话就不说了.建议使用1024X768分辨率

开始
先看下最终效果




第一步,如图所示将窗口分为四个视图




第二步,依次选择每个窗口,在分别输入各自己的视图




第三步,建立ucs重新建立世界坐标体系,捕捉三点来确定各自的ucs如图




第四步,初步大致建立基本模型.可以在主视图建立两个不同的圆,在用ext拉升,在用差集运算.如图:




第五步:关键一步,在此的我思路是.先画出卡爪的基本投影,在把他进行面域,在进行拉升高度分别是10,20,30曾t形状.如图:




第六步:画出螺栓的初步形状.如图




第七步:利用ext拉升圆,在拉升内六边形.注意拉升六边行时方向与拉升圆的方向是相反的.
之后在利用差集运算





第八步:将所得内螺栓模型分别复制到卡爪上,在利用三个视图调到与卡爪的中心对称.效果如图红色的是螺栓,最后是差集




第九步:阵列




第10步.模型就完成了




来一张利用矢量处理的图片


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条