说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 校核
1)  check [英][tʃek]  [美][tʃɛk]
校核
1.
Vacuum Checking of Liquefied Petroleum Accumulator Pot;
液化石油气贮罐真空校核
2.
Operation order generation system with self-check function for distribution network;
具有自校核功能的配电网调度操作票生成系统
2)  Verification [英][,verifi'keiʃən]  [美][,vɛrɪfɪ'keʃən]
校核
1.
Design of Verification,Validation and Accreditation Tool for Simulation System;
仿真系统校核、验证与验收工具的设计
2.
An Overview of Modeling and Simulation Verification and Validation Techniques;
建模与仿真的校核与验证技术综述
3.
Method for Verification of Complex Systems Simulation Models and Software;
复杂系统仿真模型和软件的校核方法
3)  checking [英][tʃek]  [美][tʃɛk]
校核
1.
Discussion about settings checking of ground fault protection from two external ground faults;
由两次区外故障谈定子接地保护定值的校核
2.
Theoretical checking for the results of finite element analysis of the heavy - duty cylinder barrels;
重型液压缸筒有限元计算结果的理论校核
3.
Development of checking software for deep well casing string in complex conditions
复杂工况下深井套管柱校核软件的开发
4)  verify [英]['verɪfaɪ]  [美]['vɛrə'faɪ]
校核
1.
The actual example for verifying secondary Ioaded impedance of the current transformer;
电流互感器二次负载阻抗校核实例
2.
The paper focus on the method how to set and verify the parameter of power system stabilizer(PSS) as for the power grid dispatcher s requirement.
根据调度部门需求,以励磁实测建模为基础,以PSS/E软件为计算平台,采用测试信号法计算励磁系统相位滞后特性,按照PSS相位补偿原理及临界放大倍数法,实现了PSS参数的离线整定与校核,经浙江电网实际应用证明具有较好的适应性和可信性。
3.
The system is the product of secondary development of AutoCAD using VB program,based on ActiveX automation technology,which can realize the parameterized design for standardized manipulative table in locomotive cab and verify it according to relevant locomotive criterion.
系统是在AutoCADActiveXAutomation技术的基础上,利用VB编程对AutoCAD进行二次开发实现司机室室内操纵台参数化设计,并根据规范化机车司机室的相关标准及规范对操纵台布置进行校核,从而可以快速高效地绘制出司机室设计
5)  calibration [英][,kælɪ'breɪʃn]  [美]['kælə'breʃən]
校核
1.
Design of strength calibration application program for pump shaft parts;
水泵轴类零件强度校核的应用程序设计
2.
The calibration of parameters is a key step in the application of IWA Activated Sludge Models.
对国际水协的活性污泥法动力学模型在应用中遇到的参数校核问题进行研究 ,总结了目前常用的三种方法 :专家法、灵敏度分析法和过程工程 (ProcessEngineering)法。
3.
The process frame of selection and calibration and the interface of application are presented,selecting the type of ball-bearings used for pump are completed.
用MFC与ObjectARX相结合,在AutoCAD 2002平台上开发泵用滚动轴承的选型与校核程序。
6)  intensity checking
强度校核
1.
Study on the method of intensity checking of shafts with FEA;
轴系有限元强度校核方法
2.
Based on its static,dynamic analysis and dynamic intensity checking,stress and displacement distribution as well as dynamic response of the whole system and its important components are obtained.
采用ANSYS有限元分析软件对永乐大钟及其悬挂支撑系统建立了有限元模型,进行了撞钟过程有限元瞬态分析及动力强度校核
3.
This paper analyzes the characteristic of non standard hydraulic cylinders, discourses upon the general scheme of the CAD of non standard hydraulic cylinders, and emphasizes on discussing the implementing method of the dimension driving module and intensity checking module.
分析了非标准液压缸的特点 ,论述了非标准液压缸CAD总体设计方案 ,着重分析讨论非标准液压缸CAD系统中尺寸驱动模块和强度校核模块的实现方法。
补充资料:校核
1.校对,核查。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条