说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 修配环
1)  fitting ring
修配环
2)  repair ring
修配环
1.
To determine the repair ring is the key to the method of repair settle size chain,the main task is to define the reality size of repair ring and be sure to have enough and the minimum repair volume.
修配法解尺寸链 ,确定修配环是关键 ,即主要任务是确定修配环在加工时的实际尺寸 ,保证修配时有足够的、而且是最小的修配量。
2.
It is the main problem that how to solve the repair allowance of the repair ring.
在装配时采用修配法可以获得较高的装配精度,修配法要解决的主要问题是修配环修配量的确定,针对这一问题进行了阐述。
3)  repair link
修配环
1.
Carrying out repair on the repair link for the assembly of airplanes is one of the effective methods for compensating and coordinating the accumulated errors of airplane assembly.
在飞机装配中,对修配环进行修配是补偿和协调飞机装配累积误差的有效方法之一。
4)  size of fitting ring
修配环尺寸
1.
The method of determining the size of fitting ring in time of reaching assembly precision with fitting assembly method has been studied, two formulae for calculation of the size of fitting ring have been gotten.
对采用修配法达到装配精度时修配环尺寸的确定方法进行了研究 ,给出了两个计算修配环尺寸的公式。
5)  repair and replacement
修配
1.
The repair and replacement of copper sealing strip of soft calender rolls;
压光机软辊密封铜条的修配
6)  fitting assembly
修配法装配
补充资料:模具组立修配
一.模座组立
1.量测:   尺寸量测在模具组立上是不可缺少的动作,为的是能够确认工件加工之精密度是否合乎要求之标准. 避免使用不合乎标准之零件,以确保模具减少不必要之维修,以增长模具生产之寿命.
2.修整:模板经过精密加工(铣.磨.钻.搪.攻.线割)会留下毛边和处利角,组立前必须先将各部位之毛边和利角去除.
(1)公模之修整:1.基本修整:将各部位之毛边和利角去除.
2公模板:模板须小于模盒高度0.05-0.1mm.
无滑块系统: 去除利角和毛边修整.检查是否有水孔.水孔是否攻牙.
滑块系统还必须校正滑块与导轨之间的间隙与滑动是否顺畅,不得有卡住之现象(其间隙公差)
3.辅助板: 除了去除毛边和利角修鉓外有钻孔之部部位都必须倒角,检查回位销孔是否大于回位销之直径以避免产生磨擦力,检查是否有水孔.水孔是否攻牙.
4.站脚:毛边去除和利角修鉓
5.下固定板:毛边去除和利角修鉓.
6.辅助柱修正: 辅助柱是为了要补强辅助板承受之压力,防止辅助板产生翘曲现象,又因模具的合模部位之压力均集中在较靠中间部位所以辅助柱之修整须大于站脚之尺寸0.01-0.015.
7.顶板补正: 在加工要求上辅助板顶板等,之厚度的精度要求并不会很高在这情形下会影响到顶针之长度是否凸出成品面或凹入成品面
凸出成品面-修正下顶板
凹入成品面-修正站脚和辅助柱
补正之计算方法如下:
设计值    实际值1                   实际值2
a=35       a=35.2                    a=34.8
                                     b=70 
b=70       b=70                      c=25.2
c=25        c=24.8                    e=34.8+70-25.2=79.6
d=20       e=35.2+70-24.8=80.4          小于设计值凹入成品面
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条