1) synthetic polycrystalline diamond
人造金刚石聚晶
1.
Three groups of synthetic polycrystalline diamond were sintered under different conditions, then the magnetism and abrasion ratio of the synthetic polycrystalline diamond were measured by using WCF -2 and JS71 - A respectively, while the influence of different technics and bonds on magnetism and abrasion ratio were analyzed.
结果表明:人造金刚石聚晶的磨耗比与磁性之间存在着一定的关系,即一定的烧结条件下聚晶的磁性愈强反而它的磨耗比愈小。
2.
The magnetism of the synthetic polycrystalline diamond and its raw materials including diamond powder,silicon powder,titanium powder,graphite and resultant carborundum was measured by WCF-2.
采用WCF-2多用磁性分析仪对高温高压烧结的人造金刚石聚晶及其合成原料(金刚石粉、硅粉、钛粉、石墨)和烧结过程中生成的碳化硅等进行了磁性测量。
3) synthetic single crystal diamond
人造单晶金刚石
1.
Study on laser micro-drilling technology for synthetic single crystal diamond
人造单晶金刚石激光微孔加工技术研究
4) PCD
聚晶金刚石
1.
Experimental Study on the Grindability of PCD;
聚晶金刚石磨削加工的试验研究
2.
The stress distribution of polycrystalline diamond (PCD) tool while ma chining Al2O3 ceramics overlay on compound floor is analyzed by using finite ele ment method (FEM).
采用有限元法分析了聚晶金刚石(PCD)刀具加工强化复合地板Al2O3颗粒耐磨层的应力分布状态。
3.
One kind of PCD boring tool and a fine adjustment boring bar,which are suitably used in precision finishing the surface of pinhole of combustion engine piston,are introduced.
介绍了一种适用于发动机活塞销孔表面精镗加工用聚晶金刚石镗刀和可微调刀具尺寸的精密微调镗杆 ,该镗刀和镗杆组合具有较高的加工精度和表面粗糙度精度以及调整方便、使用寿命长的特点。
5) polycrystalline diamond
金刚石聚晶
1.
Based on the analyses of current applications and performances of the polycrystalline diamonds used in drilling at home and abroad,a type of □1×1×1 interfacially grown polycrystalline diamond has been developed.
在分析国内外钻探用金刚石聚晶应用及性能的基础上,研制开发方形□1×1×1界面生长型金刚石聚晶,具体采用0。
6) polycrystalline diamond
聚晶金刚石
1.
Application status and development trends of polycrystalline diamond;
聚晶金刚石的应用现状和发展趋势
2.
Precision Mirror Grinding of Polycrystalline Diamond;
聚晶金刚石的精密镜面磨削
3.
The precision surface grinding tests on polycrystalline diamond composite(PCD) were conducted by using diamond grinding wheel.
本文采用金刚石砂轮对聚晶金刚石(PCD)复合片材料进行了精密平面磨削试验,研究了磨削工艺参数和砂轮特性对磨削力的影响规律,分析了磨削PCD材料去除机理。
补充资料：聚晶金刚石钻头
聚晶金刚石钻头
polycrystalline diamond bit
Juling】l叩angshl zuantou聚晶金刚石钻头(polyerystalline diamond bit) 以聚晶金刚石或聚晶金刚石复合片作为切削刃具的钻头。它是20世纪80年代出现的新型钻头。由于聚晶金刚石的耐磨性比硬质合金高一到两个数量级，比天然金刚石的耐磨性还要高，扩大了切削破碎的使用范围，在石油钻井、地质勘探的岩芯钻中得到推广应用，有着十分广阔的前景. 聚晶金刚石是用微米级金刚石粉和硅等加催化剂在高温高压下聚结而成，通常做成2.smm大小的立方体或边长4mm厚2.smm的等边三角形。其耐热上限可达1200℃，有较高的韧性和极高的耐磨性，可作为切削破碎岩石的刃尖， 聚晶金刚石复合片，是在厚3~smm的钨钻硬质合金薄片的基底表面烧结一层厚度为0.5~lmm的聚晶金刚石，这种结构增强了聚晶金刚石的抗冲击能力，又便于焊接，常用的聚晶金刚石复合片可直接焊接在切削面上.复合片直径在12mm以下. (黄士芳)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条