说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 工件位置误差
1)  Position error of the workpiece
工件位置误差
2)  the work piece position error
工件定位误差
3)  position error
位置误差
1.
Method for auto modification of position error of scanner;
扫描仪位置误差自动修正方法
2.
The paper analyses difficulties and characteristics in machining bearing hole of canular forked shaft and measuring its position error;and it designs equipment for machining and measuring this hole.
在叉头套加工过程中,轴承孔位置误差的测量和控制是十分重要。
3.
Measurement and compensation of volumetric position errors for NC machine tools are important approach for quality assurance and higher accuracy.
机床空间位置误差的测量和补偿是提高加工精度的重要手段。
4)  Positional error
位置误差
1.
The article establishes an optimal synthesis model based on the positional error between the practical generated paths and the desired paths, gets a synthetic result by optimization toolbox of MATLAB5.
基于连杆点实际生成的轨迹曲线与预期的理想轨迹曲线间的位置误差建立优化综合模型 ,为克服传统优化技术局限性 ,利用MATLAB中Optimization工具箱获得综合结果 ,得到一实现两平行直线轨迹的平面五连杆机构 综合实例结果表明了本方法的有效
2.
An analysis is made of the positional error of the link mechanism through the matrix theory.
利用矩阵理论对连杆机构的位置误差进行了分析,给出了有关的计算公式,并对铰链四杆机构进行了实际计算,其结果对各类连杆机构都具有普遍适用性。
3.
According to rotationplasty and move transforming characteristics of robot joints,this paper established the accurate postural and positional error model of robot,which is a homogeneous matrix.
机器人执行部件的位置误差(或精度),是反映机器人性能的一个重要指标。
5)  position-error
工位误差
6)  position error
位置度误差
1.
The principle of analyzing and evaluating the position errors of a hole is highlighted,by means if it,the geometrical reference frame of the hole group can be rotated.
着重论述了图框优化法评析孔组位置度误差的原理,详细说明了孔组位置度误差理论在现实应用中的重要性,提出了在重合公差带图中,应用孔组理论中心的旋转向量图,实现了孔组几何图框的旋转,因此在重合公差带图中即可实现孔组几何图框的平移,又可实现孔组几何图框的旋转,所以在重合公差带图中,可以用作图的方法得到孔组位置度误差(几何图框作任何运动时)。
2.
It presents the method for checking position errors of complicated irregular molding box cover with tricoordinate measuring machine, with brief description to automatic monitoring the position error in batch production by sampling checking.
介绍应用三坐标机测量不规则复杂型面箱盖位置度误差的方法,并对批量生产中位置度误差抽检监控自动测量作了简要说明。
补充资料:工件安装及所用附件

在车床上安装工件所用的附件有三爪卡盘、四爪卡盘、顶尖、花盘、心轴、中心架和跟刀架等。安装工件的主要要求是位置准确、装夹牢固。



一、三爪卡盘安装工件



三爪卡盘是车床上应用最广的通用夹具,适合于安装短圆棒料或盘类(直径较大的盘状工件中,可用反三爪夹持)工件,它的结构见示范教具。当转动小伞齿轮时,大锥齿轮便转动,它背面的平面螺纹就使三个卡爪同时向中心靠近或退出,以夹紧不同直径的工件。三爪卡盘装夹方便能自动定心,但其定心准确度不高,约为0.050.15mm。工件上同轴度要求较高的表面应在一次装夹中车出。



二、四爪卡盘安装工件



四爪卡盘的结构见直观教具。四爪卡盘有四个互不相关的卡爪,各卡爪的背面有一半瓣内螺纹与一螺杆相啮合。螺杆端部有一方孔,当用卡盘扳手转动某一螺杆时,相应的卡爪即可移动。如将卡爪调转180°安装,即成反爪。



四爪卡盘由于四个卡爪均可独立移动,因此可安装截面为方形、长方形、椭圆以及其它不规则形状的工件。同时,四爪卡盘比三爪卡盘的夹紧力大,所以常用来安装较大的圆形工件。



由于四爪卡盘的四个卡爪是独立移动的,在安装工件时须进行仔细的找正工件,一般用划针盘按工件内外圆表面或预先划出的加工线找正,其定位精度较低,为0.20.5mm。用百分表按工件精加工表面找正,其定位精度可达0.020.01mm

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条