说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 金锡合金
1)  Gold-tin alloy
金锡合金
2)  tin and tin alloy
锡及锡合金
1.
Application of lubrication protective agent on electrical contact surface of tin and tin alloy deposit
润滑保护剂在锡及锡合金镀层电接触表面的应用
3)  gold-zinc-tin alloys
金锌锡合金
4)  Cu-Sn alloy
铜锡合金
1.
Electroplated Cu-Sn alloy coating is good in decoration and solderability,low in cost,non-toxic,not irritable,etc.
电镀铜锡合金具有装饰性好、可焊性优良、成本低、无毒、不使人体过敏等优点,而得到广泛的应用。
2.
The method use SCR continuous casting-rolling system to make conducting wire(Cu-Sn alloy rod) for railway application was introduced.
介绍了采用SCR连铸连轧生产线生产高速电气化铁路接触网线用铜锡合金线坯的方法,用该法生产的产品,具有内部组织细小,均匀的晶粒,强度高,软化温度高,平直度好,耐摩性好,抗蠕变性好等特点。
3.
The paper describes the process ofφ20mm Cu-Sn alloy wirebar production in continuous casting and roiling process,analyzes the impact of the wirebar s oxygen and tin content distribution on production stability, describes the cold-forming process of contact wire manufacturing by drawing machine,and studies and compares anti-drawing strength and extension capability of it.
介绍了采用连铸连轧工艺生产φ20mm铜锡合金线坯的过程,分析了线坯氧含量、锡含量对生产稳定性的影响。
5)  tin based alloy
锡基合金
1.
The performances of lead-free plating and Sn-Pb alloy plating were contrasted, and the process formulation and operation condition of tin and tin based alloy plating and electroless plating were presented.
对比了电镀无铅镀层和Sn–Pb合金镀层的性能,给出了电镀及化学镀锡及锡基合金的工艺配方及操作条件。
2.
Gas atomizing process has been used for developing SMT purposed raw material tin based alloy soldering powder of free cleaning type soldering paste,the alloy composition and impurity component contents of which have reached US QQ SS 571E and JAP JIS Z 3282A grade standards with oxide contents meeting the standard of US Multicore Co.
采用气体雾化法研制了SMT用免清洗型软钎膏的锡基合金焊粉,其合金成分及杂质元素含量达到美国QQ-S-571E和日本JIS-Z-3282A级标准,氧化物含量达到美国Multicore公司无氧焊粉的标准,一次出粉率平均达到70%以上。
6)  zircaloy [英][,zə:kə'lɔi]  [美][,zɝkə'lɔɪ]
锆锡合金
1.
Determination of trace elements in steel, nickel-base alloy and zircaloy using time of flight inductively coupled plasma mass spectrometry;
飞行时间-电感耦合等离子体质谱法测定钢、镍基合金及锆锡合金中痕量元素(英文)
补充资料:金锡合金
分子式:
CAS号:

性质:金和锡的二元合金,共晶温度278℃,浓度为30%Sn。AuSn20、AuSn27和AuSn90等合金具有高的导热性,低的蒸气压,优良的耐蚀性,良好的浸润性和流动性。采用“热复合-冷轧”工艺制造,可轧制0.05~0.1mm的箔材。用于镀金或镀金合金的引线框架及引线的钎焊。在AuSn20合金中加入(50~300)×10-6的铂和/或钯的新钎料,有抑制钎料过分扩散和无规则漫流的作用,提高了钎焊效果。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条