1) second particle size
第二相粒子尺度
2) second phase particle
第二相粒子
1.
Effects of Processing Parameters on the Second Phase Particles in Al-Ti-B Master Alloys;
工艺参数对Al-Ti-B中间合金第二相粒子的影响
2.
Research progress of second phase particle in steel was summarized.
综述了钢中有关第二相粒子的研究进展情况,分析了第二相粒子对钢强韧性能的影响及第二相粒子细化钢晶粒的基本理论,概括了获得超细第二相粒子的基本方法,指出了存在的问题并提出了获得超细第二相粒子的新思路。
3.
By using carbon extraction replica technology and welding therma l simulation, the second phase particles in parent metal,weld metal and simulate d CGHAZ of Ti-Nb-V microalloyed steel were investigated.
利用萃取复型技术,对Ti-V-Nb微合金钢母材及模拟焊接粗晶热影响区中第二相粒子进行了研究。
3) Secondary phase particles
第二相粒子
1.
The secondary phase particles in Ti-V-Nb microalloyed linepipe steel were investigated using carbon extraction-replica technique.
利用萃取复型分析技术 ,对Ti V Nb微合金管线钢中第二相粒子进行了研究。
2.
The secondary phase particles in dual-phase steel were investigated by using carbon extraction-replica technique.
本文采用萃取复型分析技术,对低 Si-Mn 双相钢中的第二相粒子进行了研究。
4) the second phase particle
第二相粒子
1.
The results show that the second phase particles in sintering block are sphere-like and arranged mainly on crystal interfaces; the second phase particles in rolling block are needle-like and distributed in or on crystal interfaces, and some even span several grains; the second phase particles in annealed wire are arranged in lines, and in many bunches of particles and distributed i.
对AKS合金中第二相粒子在烧结、轧制和拉拔各个工序中组织形貌的演变及演变机理进行研究。
2.
The paper study the microstructure,the second phase particle precipitating,dislocations strengthening in different TMCP conditions to optimize the technological condition for lager industrialized production.
通过研究不同TMCP工艺下实验钢的微观组织、第二相粒子析出和位错强化等规律,优化最佳的生产工艺,为工业化大生产提供必要的指导。
5) second-phase particle
第二相粒子
1.
Computer simulation of grain growth(Ⅱ)——influence of shape and orientation of second-phase particles on grain growth;
正常晶粒长大的计算机模拟(Ⅱ)——第二相粒子形状及取向的影响
2.
The pattern and distribution of second-phase particles in the different processes were analyzed and the mechanical properties were measured at the same time.
068%Ti(质量分数)的Ti-IF钢在铁素体区热轧、冷轧和再结晶过程中其微观组织和织构的变化规律,重点分析了不同阶段的第二相粒子的形态与分布情况,并对其力学性能进行了测试。
3.
Based on the ordinary grain growth cellular automaton(CA) model,a novel transition rule was established to simulate the influence of second-phase particle size on grain growth process.
在现有晶粒长大元胞自动机器(CA)模型的基础上制定新的转变规则,使之能够模拟第二相粒子对晶粒长大过程的影响,且对含有不同尺寸第二相粒子材料的晶粒长大过程进行仿真模拟和定量分析。
6) second phase particles
第二相粒子
1.
Second Phase Particles in CGHAZ and Weld of Ti-V-Nb Microalloyed Pipeline Steel;
Ti-V-Nb微合金管线钢焊缝及热影响区中第二相粒子
2.
The effect of the second phase particles formed during different aging processes on stimulating nucleation of recrystallization and its grain size of 01420 Al-Li alloy were investigated by means of optical microscopy (OM),scanning electron microscopy (SEM) and transmission electron microscopy (TEM).
通过光学显微镜、扫描电镜及透射电镜观察,研究01420铝锂合金的第二相粒子对激发再结晶形核和晶粒大小的影响。
3.
The recent development on the precipitation of the second phase particles in Ti IF steels was reviewed, in which the following topics were involved: the kinds of the second phase particles in Ti IF steels; the precipitation process of the second phase particles during the hot rolling; the effect of the chemical composition and the hot rolling parameters on the precipitation behaviour.
介绍了有关 Ti- IF钢热轧时第二相粒子析出行为的一些最新研究成果 ,内容包括 :第二相粒子的种类 ;第二相粒子在热轧时的析出过程 ;化学成分和热轧工艺参数对第二相粒子析出行为的影响。
补充资料：初级粒子和原级粒子
分子式：
CAS号：
性质：又称初级粒子和原级粒子。利用各种化学反应方法得到的最初粒子(晶粒)。一次粒子的大小约为0.005～1μm，比筛分的极限小得多，在介质中有相当高的稳定性。
CAS号：
性质：又称初级粒子和原级粒子。利用各种化学反应方法得到的最初粒子(晶粒)。一次粒子的大小约为0.005～1μm，比筛分的极限小得多，在介质中有相当高的稳定性。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条