1) dynamic mold temperature control
变模温控制
1.
Several dynamic mold temperature controlling techniques in micro injection molding, including heat pipe heating plus water cooling, induction heating, thin film resistance heating, composite mold wall heating plus insulation, composite mold wall insulation plus compressing, and preheated air heating were introduced.
阐述了变模温控制在微注射成型中的重要性,介绍、比较了当前出现的电热水冷、感应加热、薄膜电阻式加热、复合模壁绝热一加热、复合模壁绝热压缩热空气加热几种变模温控制实现方法,展望了未来微注射成型中变模温控制的发展趋势。
2) catastrophe model
突变模型
1.
The elastic incline beam catastrophe model for instability of tunnel stratiform surrounding rock;
隧道层状围岩失稳的弹性倾斜梁突变模型
2.
A catastrophe model for dynamic fracture of static loaded rock;
受静载荷作用的岩石动态断裂的突变模型
3.
The systemic and theoretical analysis of the gestation and outburst process of coal and gas outburst on an intuitive basis by setting up the cusp catastrophe model of coal and gas outburst results in the mechanism and qualification of gas outburs.
通过建立煤与瓦斯突出的尖点突变模型,较为直观的对突出的孕育过程和突出过程作出了系统的理论分析,得出了瓦斯突出启动的突变机制和突变条件,从而为煤与瓦斯突出灾害预测与防止提供了新的理论依据。
3) creep model
蠕变模型
1.
Non-linear creep model of rock and parameter determination;
岩石试件非线性蠕变模型及其参数确定
2.
Study on nonlinear creep model for saturated sand;
饱和砂性土非线性蠕变模型试验研究
3.
A creep model based on modified time hardening theory is promoted to simulate the short duration creep behavior of PBX components.
利用基于修正时间硬化理论的蠕变模型来模拟炸药部件的短时蠕变行为。
4) rheological model
流变模型
1.
Study about permeability and foundation of rheological model in resin film infusion process;
RFI成型工艺中渗透率的研究及树脂流变模型的建立
2.
A rheological model study of fluid adsorption at the wall surface;
流变模型壁表面对流体吸附作用的研究
3.
Characteristics of saturated loess and rheological model of unsaturated loess in Xi’an;
饱和黄土的性质与非饱和黄土流变模型
5) variable modulus method
变模数法
1.
In accordance with low design precision and efficiency of compacting die for P/M gears,a new variable modulus method in designing and calculating the compacting die for P/M gears is introduced.
针对目前粉末冶金齿轮成形阴模设计精度和效率低的特点,介绍了用变模数法设计计算粉末冶金齿轮成形阴模的新方法,并以Pro/E为开发平台,以Pro/Program为开发工具,进行粉末冶金齿轮成形阴模的程序化设计,从而提高了粉末冶金齿轮成形阴模的设计精度和效率。
6) thixo-forging
触变模锻
1.
Numerical Simulation of Semi-solid Thixo-forging for Light Alloy;
半固态轻合金触变模锻成形数值模拟
2.
Y112 aluminum alloy thixo-forging experiment in semi-solid state was carried out.
对Y112铝合金进行半固态触变模锻实验,确定了该试验最优的半固态二次加热工艺参数。
参考词条
补充资料：临机制变
1.犹言临机应变。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。